Wolf E Series SO30-2F/S Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 20

Wolf E Series SO30-2F/S Скачать руководство пользователя страница 15

15

I N S TA L L AT I O N

I N S T R U C T I O N S

Dimensions in parentheses are in
millimeters unless otherwise specified.

E L E C T R I C A L

R E Q U I R E M E N T S

With the oven positioned directly in front of
the cabinet opening, feed the conduit through
the opening in the cabinet platform (where
applicable). Then, depending upon local codes,
utilize one of the following techniques to
connect the appliance to the electrical power
supply.

To connect to a four-wire electrical system,
follow these steps:

Connect one hot lead to the black (L1)
power supply wire in the electrical box.

Connect the other hot lead to the red (L2)
power supply wire in the electrical box.

Connect the ground wire to the green/
ground house grounding wire in the
electrical box.

To connect to a three-wire electrical
system, follow these steps:

Connect one hot lead to the black (L1)
power supply wire in the electrical box.

Connect the other hot lead to the red (L2)
power supply wire in the electrical box.

Connect the ground wire to the green/
ground house grounding wire in the
electrical box.

Leave the white neutral floating (not
connected to anything, but sealed off
with a wire cap).

I N S TA L L I N G

T H E O V E N

U N P A C K T H E O V E N

Cut the plastic straps and remove the two
V-boards. Remove the four top foam corners
and the corner posts. Remove the carton
sleeve by lifting the sleeve up and over the
appliance.

Remove all oven racks, oven rack guides and
broiler pan from inside the oven cavity. For the
double oven, be sure to do this for both the
upper and lower ovens.

Remove the four bottom corners. Use caution
as the oven is not mounted to the shipping
base. Keep the bottom foam in place when
moving or carting the oven. The bottom foam
also protects the factory-installed trim.

IMPORTANT NOTE: Before moving the oven,
protect any finished flooring with appropriate
materials to avoid damage to the floor.

Remove and discard all packing materials,
including cardboard and tape on the outside of
the oven and inside the oven cavity.

Oven is not mounted to the shipping
base. Do not remove banding until the
oven is at the point of installation.

Do not remove the bottom foam until
oven has been positioned next to the
installation opening.

Do not lift the unit by the oven door
handle(s). This will damage the oven door
and hinges.

«
...
13
14
15
16
17
...
»

Содержание E Series SO30-2F/S





















Отзывы:

Нет отзывов