Wolf 4380000 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Wolf 4380000 Скачать руководство пользователя страница 5

Page 5

6-35

7040317 - Revision A - September, 2015

Built-In (BI) Series

Built-In (BI) Series

(SWS #4380000)

(SWS #4380000)

Component Removal

Framed / Overlay Door Handle / Handle-Side Trim

The door handle on framed units and the handle-side
trim on overlay units is attached to the door with
screws. These screws are covered by a screw cover.

To remove a handle of handle-side trim, open the door
then:

1. At the top of the door, insert a flat blade screwdriver

into the channel of the screw cover and push the
cover back, disengaging it from the handle or trim
(See Figure 6-85).

2. With a T-20, 6-lobe Torx type bit, extract the handle-

side trim mounting screws and pull the trim from the
door (See Figure 6-86).

Stainless Steel Door Handle Assembly

A screw inserted through the stainless steel handle
standoffs into the handle secures the handle to the
standoffs. The standoffs are then slides over threaded
studs that are attached to the door shell. A socket head
set-screw inserted through the side of the standoff
secures the standoff to the stud.

To remove a stainless steel handle assembly (See
Figure 6-87):

1.

Use a 3/32” Allen-wrench to loosen the set-screw in
each handle standoff.

2.

Pull handle assembly off of the threaded studs.

DOOR

SCR

EW COVE

R

HANDLE-SIDE TRIM

Figure 6-85. Screw Cover Removal

HANDLE-SIDE TRIM

DOOR

Figure 6-86. Handle / Handle-Side Trim Removal

Figure 6-87. Cut-away View of SS Handle Assembly

Handle Mount

Screw

Threaded Stud

Set-Screw

Handle Standoff

Handle

«
...
3
4
5
6
7
...
»

Содержание 4380000





















Отзывы:

Нет отзывов