manualshive.com logo in svg

Wolf 4380000, Руководство по обслуживанию, Страница: 3 / 20

Поделиться
Скачать
Wolf 4380000 Скачать руководство пользователя страница 3

Page 3

6-33

7040317 - Revision A - September, 2015

Built-In (BI) Series

Built-In (BI) Series

(SWS #4380000)

(SWS #4380000)

Component Removal

Water Valve Assembly

NOTE: 

Before attempting to remove an isolation &/or

water valve assembly, switch the water supply to the
unit off.

To remove a valve assembly (See Figure 6-79):

1.

Extract valve assembly mounting screws and pull
valve forward.

2.

Disconnect AC (and DC if applicable) electrical
leads.

NOTE:

It may be necessary to cut a cable tie that

is securing the AC electrical leads to the valve
assembly.

3.

Disconnect inlet and outlet water tubes from valve
by pushing the collar around the tubes toward the
valve, while pulling the tubes away from the valve.

Grille Assembly

The grille assembly is attached at the top of the unit
with screws passing through the grille’s side frames into
grille brackets.

To remove a grille assembly (See Figure 6-80):

1.  Lift open the front of the grille assembly to access

the mounting screws.

2.  With a T-20, 6-lobe Torx type bit, extract the two

front grille mounting screws, then loosen but do not
remove the two rear mounting screws.

3.

pull the grille assembly forward, off of the unit.

NOTE: 

When reinstalling the grille assembly, line up

the notches at back of grille side frames with the rear
mounting screws, then push the grille assembly back.

Water Filter

The water filter and manifold are located at the right-
hand top side of the unit behind grille assembly.

To remove the filter, first lift open the front of the grille
assembly, then (See Figure 6-81):

1.

Rotate filter counterclockwise to remove it (clock-
wise to install it).

2.

Then pull cartridge out of the manifold.

NOTE:  

After a filter cartridge has been replaced, the

reset button behind the unit grille must be pressed for
five (5) seconds to clear the filter icon from the LCD
and reset the water filter timer.

Figure 6-79.  Water Valve Removal

DC Connection

AC Connection

Collar

Inlet Tube

Outlet Tube

Figure 6-80  Grille Assembly Removal

Grille Mounting Screws

Grille Assembly

Grille Bracket

Grille Bracket

Figure 6-81.  Filter Removal

Water Filter

Содержание 4380000





















Отзывы:

Нет отзывов