Wolf 126620 Скачать руководство пользователя страница 21

Страница: 21 / 64

FULL SIZE GAS CONVECTION OVENS - SERVICE PROCEDURES AND ADJUSTMENTS

F32700 (February 2006)

Page 21 of 64

Reverse procedure to install.

TEMP (°F)

OHMS*

TEMP (°F)

OHMS*

90000

360

822

240

4077

380

656

260

3016

400

529

280

2266

425

424

300

1726

450

334

320

1332

475

266

340

1041

(*) Resistance in ohms ± 10%

GAS PRESSURE ADJUSTMENT

WARNING:

DISCONNECT THE

ELECTRICAL POWER TO THE
MACHINE AND FOLLOW LOCKOUT /
TAGOUT PROCEDURES.

WARNING:

SHUT OFF THE GAS BEFORE

SERVICING THE UNIT.

Remove the right side panel as outlined under
COVERS AND PANELS in REMOVAL AND
REPLACEMENT OF PARTS.

NOTE:

If right side panel is not accessible, this

component can be serviced by removing the control
panel as outlined under COVERS AND PANELS.

Remove the plug from the manifold pressure
port.

Install hose barb adapter and attach manometer
tube.

Remove adjustment screw cap from the gas
valve and turn gas supply to the oven back on.

Plug the unit in and turn the power switch ON.

Set the temperature control to its highest setting
and allow burner to ignite.

NOTE:

Accurate gas pressure adjustments can only

be made with the gas on and the burner lit.

Turn the set screw to obtain the proper gas
pressure (clockwise = pressure increase;
counterclockwise = pressure decrease).

GAS

TYPE

PRESSURE READINGS (IN W.C.)

MANIFOLD

LINE

RECOMMENDED MIN

MAX

Natural

3.5

Propane

NOTE:

If the incoming line pressure to the valve is

less than the minimum stated, then the manifold
pressure can not be set correctly.

Содержание 126620

































































Результаты поиска

Содержание 126620

Отзывы:

Wolf 126620, Руководство по обслуживанию, Страница: 21 / 64

Результаты поиска

Содержание 126620

Отзывы: