WMF 1500S+ Скачать руководство пользователя страница 90

Страница: 90 / 120

User Manual WMF 1500 S +

Care | Manual cleaning

5.5.9 Clean the mixer

Cleaning will be more frequent depending on powder
consumption.

Scalding hazard

•

If the mixer hose is not firmly attached,
hot water or hot powder beverage can be
discharged inadvertently.

> Always firmly place on the mixer hose.

Slide the operating panel upward

Pull the mixer hose off of the combi spout and use
the handle to move the mixer bowl upward

The propeller for the mixer is now visible.

Daily

Remove the mixer bowl

Disassemble the mixer bowl into its four component
parts

Thoroughly clean the parts under running drinking
water

When needed (weekly)

Mix 5 ml of WMF special cleaner or a special
cleaning tablet with 0.5 litres of warm drinking
water

Immerse all four parts in the cleaning solution at
least for 4 hours

After 4 hours, thoroughly rinse under running
drinking water again

Remove the powder hopper and clean the loading
shaft to the mixer bowl with a cloth or brush

Allow the parts to dry completely

On re-assembly, all openings must face in the same
direction.

Attach mixer hose on the mixer bowl

Replace mixer bowl until she engages in the lock

Attach mixer hose on the combi spout

CaUtion

Follow the Safety chapter

starting on page 7

Instructions

Main menu

Care

Instructions

Содержание 1500S+

























































































































Результаты поиска

Содержание 1500S+

Отзывы:

Похожие инструкции для 1500S+

Бренды по названию

Популярные бренды

WMF 1500S+, Руководство пользователя

Результаты поиска

Содержание 1500S+

Отзывы:

Похожие инструкции для 1500S+

Бренды по названию

Популярные бренды