WM Systems M2M Industrial Router Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 79

background image

Caution!

By general the device is using DC mains. 9-24V DC mains electric shock (12..24V DC)
hazard inside the enclosure! DO NOT open the enclosure and DO NOT touch the PCB.

(Consumption: 1.9W during 2G/3G communication, 2.9W during LTE communication)

The IP51 immunity protection will be effective only in case of under normal usage and
operation conditions with unharmed hardware conditions by using the device in the
provided enclosure/chassis.

Deliberate damage or occing casualty of the device means the loss of product warranty.

To ensure general safety, please follow the following guideline:

■

Keep the chassis area clear and dust-free during and after installation.

■

Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll

up your sleeves.

■

Do not perform any action that creates a hazard to people or makes the equipment unsafe.

Safety with Electricity

Follow this guideline when working on equipment powered by electricity.

■

Read all the warnings in Safety Warnings.

■

Locate the emergency power-off switch for your installation location. If an electrical accident

occurs, you can quickly turn off the power.

■

Disconnect all power before:

–

Installing or removing a chassis

–

Working near power supplies

■

Look carefully for possible hazards in your work area, such as moist floors, ungrounded power

extension cables, frayed power cords, and missing safety grounds.

■

Do not work alone if hazardous conditions exist.

■

Never assume that power is disconnected from a circuit. Always check.

■

Never open the enclosure of the router’s internal power supply.

«
...
5
6
7
8
9
...
»

Содержание M2M Industrial Router
















































































Отзывы:

Нет отзывов

Похожие инструкции для M2M Industrial Router

Бренд: 3xLogic Страницы: 2

Бренд: Garland Страницы: 4

StorTrends 1312-P

Бренд: American Megatrends Страницы: 2

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

EonServ 5000 Series

Бренд: Surveon Страницы: 33

Бренд: Telex Communications Страницы: 28

Бренд: Justec Страницы: 61

Бренд: 3Com Страницы: 32

Бренд: Supermicro Страницы: 27

Бренд: IMC Networks Страницы: 36

ReadyNAS 3220 Series

Бренд: NETGEAR Страницы: 4

Бренд: Airlinkplus Страницы: 20

Бренд: Alcatel-Lucent Страницы: 12

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренд: e+p Страницы: 2

Бренд: CTC Union Страницы: 12

Бренд: Axtrinet Страницы: 49

GigaSpire BLAST u6

Бренд: Calix Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды