Wizard MatDesigner 5000 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 26

Wizard MatDesigner 5000 Series Скачать руководство пользователя страница 21

\Manuals\5000Hardware

07/07/03

9

Series 5000 Hardware Guide

V-groove Washer keeps Blade from penetrating matboard by the thickness of the washer.

Fig A.

Fig B.

Fig A: V-Groove Washer. Fig B: The V-Groove Washer is placed on the Blade Depth Adjustment Screw.

Head Removal

1. L-click Reset Motors (menu option) to disengage Motors. Removing the Head Hood (held with Phillips screws w/star wash

-

ers) will make access to the Head Power Plug easier. Remove Blade.

2. Unplug Head Power Plug by gripping white plug housing firmly (not flexible cable), and gently rock it back and forth while

pulling up (Fig A).

Fig A.

Fig A: Head Power Plug is plugged into Trolley Plate with the notched end down.

3. Disconnect air supply (Fig B). Disconnect the Air Line by unscrewing airline connector.

Fig B.

Fig B: Disconnect Air Line on the Head.

4. Open Head. Remove Horizontal Bolt from Head and right Hinge on the Trolley Plate using the 9/64 Allen Wrench (Fig
C-D).

«
...
19
20
21
22
23
...
»

Содержание MatDesigner 5000 Series



























Отзывы:

Нет отзывов