22
www
.wittur
.com
Changes can be made without notice
PM.2.004922.EN - 810-000-000 SRS DC-PWM
©
· Edition 22 July 2020
8.3 SELF-LEARNING CYCLE USING THE HANDSET
By using the handset to operate a self-learning cycle, interferences with possible signals coming from the main lift controller are avoided
•
Power the system
•
Turn “ON” the door controller; if there are any closing or opening signals from the main lift controller, the operator will perform the
relevant reset cycle in low speed up to the end run limit
•
Connect the handset to RJ45 connector
•
Using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the MAIN MENU and choose “SELF LEARNING”
•
Using the “OK” key confirm the option
•
If the operator is not on a closing position use key F2 (><) to allow the door to complete a closing cycle in low speed
•
Once the closure has been made, push again key F2 (<>) to allow a complete opening cycle in low speed
During this operation please check carefully that the operator completes its total expected travel.
At the end of the opening cycle the self-learning cycle is completed.
This will be signalled with the information “Self-learning completed”.
•
Press key F1 (EXIT) to restore the “MAIN MENU ”
8.4 SPEED PROFILE ADJUSTMENTS USING THE HANDSET
This option allows the modification of the speed profiles, on the handset display are shown all the possible trimmer settings (see
•
Connect the handset to RJ45 connector
•
Using keys
ã
and
ä
choose the required language and confirm with the “OK” key
•
Using keys
ã
and
ä
run through the “MAIN MENU” and choose “PROFILE SETTINGS”;
•
Press the “OK” key to confirm the option
•
On the display the following options are viewed:
−
High speed OP XX %
−
Low speed OP XX %
−
High speed CL XX %
−
Low speed CL XX %
−
Revers. force XX N
−
Acc.AP
−
Dec.AP
−
Acc.CH
−
Acc.CH
•
Using keys
ã
and
ä
to run through the menu “PROFILE SETTINGS” and choose the required option
•
Use keys
á
and
â
to increase or decrease the selected parameter current value (percentage of the maximum value for the speed
or the exact newton value for the reversing force).
•
Press key F2 (<> - ><) to check the door operation with the new set profile
•
To save in permanent memory the set value press
ã
or
ä
or key F3
•
The following options are available:
−
"MENU": press key F3 to restore the "MAIN MENU";
The value shown in this menu is connected to the trimmer set value: modifying one trimmer position you can see the real time parameter variation on the handset
display (for trimmer rotations over the 4% of the maximum value)
8.5 GENERAL OPTIONS
•
Connect the handset to RJ45 connector
•
Use keys
ã
and
ä
to choose the required language and confirm with the "OK" key.
•
Use keys
ã
and
ä
to run through the "main menu" and choose "GENERAL OPTIONS";
•
Press the "OK" key to confirm the option
•
The GENERAL OPTION menu allows the Door Controller to operate by means of the following parameter option:
−
CLOSING ROTATION
−
SKATE TYPE
−
CLOSING REST TYPE
−
MOTOR
−
MAX CURRENT END CL
−
LA THRESOLD
8.5.1 Closing Rotation with the Handset
•
“6.3 Motor Rotation during closing” a pag. 15
for the meaning of this parameter
•
Using keys
ã
and
ä
, run through the GENERAL OPTIONS and choose the CLOSING ROTATION option
•
Press the “OK” key to confirm the choice
•
The following options are viewed on the display:
−
CLOCKWISE
−
ANTICLOCKWISE
•
Using keys
ã
and
ä
, choose the required option and press the “OK” key to confirm it
•
The display shows the confirmed option and restores the menu GENERAL OPTIONS
•
The following options are available:
