WisyCom MTP51-JP Скачать руководство пользователя страница 6

MTP51-JP User Manual

 

 

 

 

6

 

 

CLICK
 

Using <+/-> selector all menus can be accessed in sequence, push <click> to enter edit mode: 

<+/-> to setup field 
<click> again to confirm changes and exit. 

exit without confirmation

 

if no button is pressed after a few seconds time out. 

 

<START UP>  

These menus are displayed during power up for few seconds  

First one gives information of antenna to be used. The number displayed is code of the antenna to 
be used..  

The second menu gives indication on product: 
- product id (MTP51-JP),  
- the firmware release (ex. 

1.30.0Y

),  

- the band in extended format  
- the serial number. 

Keep selector pushed to hold this menu!

 

<STATUS>  

This is the first menu displayed after power up.  
Major info are displayed: 

 

Current channel/group (i.e. CH:00 GR:39) 

 

Current frequency (i.e. 566.000 MHz) 

 

Mic gain (i.e. AF: +00dB) and high pass filter (i.e. HP:60 Hz) 

If in the top right there is “RF 50” or “RF 10”, the transmission is active respectively  at 50mW or 
10mW 

    On left side, the battery bar is displayed 

<PRESET>  

This menu can be entered by scrolling selector  
MTP51-JP can recall configuration presets.  

“FACTORY” recalls the Wisycom factory configuration.  
“USER” recalls the user configuration (the transmitter configuration 
is copied into the USER using the “save to” submenu).  

All “USER” menus are not locked by default, thus this is quick way to unlock features! 

When the user changes some parameters from the PRESET configuration (for less than frequency) an 
asterisk appears on the top-right corner until a save command is executed. 

The other  8 configuration presets are user programmable thru the infrared and the PC interface (using 
the programmer UPK

Mini

 or the receiver MRK950/MRK960).  

We  provide  the  device  with  some  preset  configurations  specifically  designed  for  certain  types  of 
microphone or applications (it’s possible to change these presets in any time using Wisycom Manager). 
All parameters can be “left unchanged”, “changed” or “changed and lock”, allowing a very flexible way 
to pre-program MTP51-JP configuration.   
 

Содержание MTP51-JP













Отзывы: