background image

 

Industry Canada statement: 

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, 

Science and Economic Development C

anada’s licence-exempt RSS(s). Operation is 

subject to the following two conditions:   

(1) This device may not cause interference 

(2) This device must accept any interference, including interference that may cause 

undesired operation of the device   

Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes 

au (x) RSS (s) exemptés de licence d'Innovation, Sciences et Développement 

économique Canada. L'opération est soumise aux deux conditions suivantes: 

(1) Cet appareil ne doit pas causer d'interférences 

(2) Cet appareil doit accepter toute interférence, y compris les interférences pouvant 

provoquer un fonctionnement indésirable de l'appareil 

This radio transmitter (IC: 409B-DHUKSY22) has been approved by Industry Canada to 

operate with the antenna types listed below with the maximum permissible gain indicated. 

Antenna types not included in this list, having a gain greater than the maximum gain 

indicated for that type, are strictly prohibited for use with this device. 

 

Le présent émetteur radio (IC: 409B-DHUKSY22) a été approuvé par Industrie Canada 

pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain 

admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est 

supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de 

l'émetteur. 

 

Antenna 

2.4GHz Antenna 

Peak gain (dBi) 

5GHz Antenna 

Peak gain (dBi) 

WiFi ANT0 

-0.52 

4.24 

WiFi ANT1 

2.82 

1.91 

BT Antenna 

-0.26 

 

 

Caution:   

 

(i) the device for operation in the band 5150

–5250 MHz is only for indoor use to reduce 

the potential for harmful interference to co-channel mobile satellite systems;   

 

Содержание DHUK-SY22

















Отзывы: