Wisstar WP-ABV2E-IR4 Скачать руководство пользователя страница 5

Страница: 5 / 15

1.2.2

Type II Camera Overview

Mounting

Base

Trim Ring

Enclosure

Camera

Video

Cable

Switch

Button

Power

Cord

Figure 1. 2

Type II Camera Overview

Note:

Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs
are available: TVI, AHD, CVI, and CVBS.

1.2.3

Type III Camera Overview

Enclosure

Trim Ring

Mounting

Base

Main Body

Video

Cable

Power

Cord

Switch

Button

Figure 1. 3

Type

III Camera Overview

Note:

Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

Installation

Installation Preparation

Before you start:

⚫

Make sure that the device in the package is in good

condition and all the assembly parts are included.

⚫

Make sure that all the related equipment is power

off

during the installation.

⚫

Check the specification of the products for the

installation environment.

⚫

Check whether the power supply is matched with

your power output to avoid damage.

⚫

Make sure the wall is strong enough to withstand

three times the weight of the camera and the

mounting bracket.

⚫

If the wall is cement, you need to insert expansion
bolts before you install the camera. If the wall is

Содержание WP-ABV2E-IR4
















Результаты поиска

Содержание WP-ABV2E-IR4

Отзывы:

Бренды по названию

Популярные бренды

Wisstar WP-ABV2E-IR4, Руководство пользователя

Результаты поиска

Содержание WP-ABV2E-IR4

Отзывы:

Бренды по названию

Популярные бренды