Wisstar WP-ABV2E-IR4 Скачать руководство пользователя страница 4

Страница: 4 / 15

⚫

The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

⚫

Do not place the camera in extremely hot, cold, dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

⚫

To avoid heat accumulation, good ventilation is

required for operating environment.

⚫

Keep the camera away from liquid while in use.

⚫

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Mark Description

Table 0

1 Mark Description

Mark

Description

DC Voltage

Introduction

Product Features

The main features are as follows:

⚫

High performance CMOS sensor

⚫

1080p/720p resolution

⚫

Auto white balance

⚫

Auto electronic shutter

⚫

Auto gain control (AGC)

⚫

Switchable TVI/AHD/CVI/CVBS video output

⚫

IR cut filter

⚫

axis adjustment

Note:

Type III camera is applicable for indoor only.

Overview

1.2.1

Type I Camera Overview

Video Cable

Power Cord

Switch Button

Mounting

Base

Main Body

Lens

IR LED

Figure 1. 1

Type

I Camera Overview

Note:

Press and hold the switch button for 5 seconds to
switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

Содержание WP-ABV2E-IR4
















Результаты поиска

Содержание WP-ABV2E-IR4

Отзывы:

Бренды по названию

Популярные бренды

Wisstar WP-ABV2E-IR4, Руководство пользователя

Результаты поиска

Содержание WP-ABV2E-IR4

Отзывы:

Бренды по названию

Популярные бренды