background image

installation & connection

10_

 installation & connection

Installing by wall mount

1. 

Using a Torx L wrench, turn the three screws counterclockwise to remove the 
housing.

2. 

Pull off the extruded part of the 1-hole cable 
bushing provided.

3. 

Use the cap installer to route the network cable 
through the cable bushing.

 

J

 

`

If you use a network cable that does not fit into the 
cap installer, the cable bushing will be damaged and 
the waterproof function will not work properly.  
Please use the RJ45 connector, which does not 
damage the cable bushing.

4. 

Insert the cable bushing into the groove of the housing installation unit. 

Removing a Micro SD Card

Gently press down on the exposed end of the memory card as shown in 
the diagram to eject the memory card from the slot.

 

J

 

`

Before removing the Micro SD card, in <

Setup ( 

 )

>-<

Event

>-<

Storage

>, 

set the device to <

Off

> and press the [

Apply

] button and turn the camera off.

 

`

If you turn off the camera or remove the Micro SD card that contains data from 
the product, the data may be lost or damaged.

Preparing & Installing Camera Bracket

For installation guidelines for brackets and housings, refer to the installation manual that is enclosed with the 
bracket or housing.

 

M

 

`

See “

Optional Accessories for Installation

” for the appearance of each bracket (unbundled).  

(page 7)

Содержание QNP-6320HS
























Отзывы: