manualshive.com logo in svg

Wiseair WAFS-103, Руководство пользователя

Поделиться
Скачать
Wiseair WAFS-103 Скачать руководство пользователя страница 3

User Manual

2021 Release 2

WiseAir Technologies India LLP

[email protected]  +91 90477 78715

WAFS 103 DIFFERENTIAL

PRESSURE PITOT TUBE FLOW METER

Page 3 of 32

MEASURE TO MANAGE

Section 1 : General Information :

 

1.1

    Please  read  this  user  manual  in  full  and  carefully  observe  the  notes  and 

instructions  before  and  during  installation,  operation  and  maintenance.  The  manufacturer 
cannot  be  held  liable  for  any  damage  which  occurs  as  a  result  of  non-observance  or 
noncompliance with this user manual.
 

Should the device be tampered with in any manner other than a procedure which is 

described  and  specified  in  this  manual,  the  warranty  is  cancelled  and  the  manufacturer  is 
exempt from liability. The device is designed exclusively for the described application.
 

This user manual should be read carefully by the technician / qualified personnel and 

the end user. Once you install, use or maintain this product, you accept that you have read, 
understood and complied with this manual. This manual should be kept with the Flow Meter and 
made available to relevant personnel as needed. WiseAir Endeavours to make changes to the 
content of this Manual, and tries to ensure Correctness and well stated, but is not responsible for 
Omissions or errors and the consequences caused thereby.

 

1.2 

 

Compressed Air Safety

 

Any contact with quickly escaping air or bursting parts of the compressed air system 

can lead to serious injuries or even death.
 

 

Do not exceed the maximum permitted pressure

 

 

Only use pressure tight installation material.

 

 

Avoid getting hit by escaping air or bursting parts.

 

 

The system must be pressure-less during maintenance work.

 

1.3 

 

Electrical Safety

 

Any contact with energised parts of the product, may lead to an electrical shock which 

can lead to serious injuries or even death.Consider all regulations for electrical installations.
 

The system must be disconnected from any power supply during maintenance work.

 

Any electrical work on the system is only allowed by authorised qualified personal.

 

 

1.4  Installing the Flow Meter, Calibration & Maintenance

 

 

The product must be installed properly and frequently calibrated, otherwise it may 

lead to the wrong measurement values, which can lead to wrong results.
 

 

  

Always  Observe  the  Direction  of  Flow  When  installing  the  Sensor.  The

 

 

  

Direction is Indicated on the Housing.

 

 

  

Do Not Exceed the Maximum Operation Temperature at the Sensors Tip.

 

 

  

Avoid Condensation on the Sensor Element as this will affect the accuracy

 

 

  

enormously.

 

 

  

Please observe national regulations before/during installation and

 

 

  

operation.

 

 

  

Do not disassemble the product.

 

 

  

Always use a spanner to mount the product properly

Содержание WAFS-103

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды