background image

 

10 

the woofer separately from the drivers that handle the midrange and treble 
frequencies.  

Logically, you can combine these two approaches, and the result is “tri-
amplification.” A “tri-amped” system uses separate amplification for three audible 
ranges.  In our case, the three ranges are: 

 

deepest bass (one or more subwoofers) 

 

mid-bass (the woofers in the front and surround speakers) 

 

midrange and treble (the planar magnetic panels) 

Since each channel of the amplifier is delivering current into its load only over a 
limited range of frequencies, several forms of distortion are reduced as compared to 
each channel handling the full range of musical information. 

 

The SC-2 supports up to 8 channels of inputs (all of which could be bi-amplified), 
and 16 output channels all with Dirac, and also their own independent user EQ 
and channel delay. 

 

System-Specific EQ:

 Wisdom Audio speakers deliver extraordinary performance 

from slim, elegant enclosures.  However, we cannot cheat the rules of physics. 
Delivering powerful bass from such small enclosures places unusual demands on 
both the woofers and the amplifiers used to drive them. 

 

Specifically, equalization is used to compensate for the unusually small enclosure 
volume behind the woofer.  This approach is used in almost all dedicated 
subwoofers today, and we use it in our full range speakers.  Doing so allows us to 
achieve the bass performance usually associated much larger speakers, but in 
elegant enclosures that support modern lifestyle choices. 

 

 

 

 

 

 

 

Front Panel

 

Содержание SC-2
























Отзывы: