manualshive.com logo in svg

Wisdom AUDIO SYSTEM CONTROLLER SC-1, Руководство пользователя

Поделиться
Скачать
Wisdom AUDIO SYSTEM CONTROLLER SC-1 Скачать руководство пользователя страница 42

42

boost in the bottom octave before you get too carried away with 
this setting.

•  The SMPTE 202M curve is also known as the “X-curve” and is an 

international standard for the high frequency roll-off applied in a 

typical 500-seat movie theater. It is appropriate for professional 
mixing spaces and dubbing stages that must be calibrated for film 
sound postproduction. It can also be used in extremely large play-
back spaces (room volume greater than 5000 cu. ft.) 

With the three setup memories available in the SC-1, it is possible to take advan-

tage of multiple target curves. 

For example, it is a relatively simply matter to use EQ 1 for movies, in which a 
Flat target curves and THX processing in the surround processor is most appro-

priate; EQ 2 could be used for music listening, where the Standard HF Rolloff is 

usually the more desirable target; and EQ 3 might include the Gaming curve for 
your XBox or Playstation 3 exploits, or simply when you would like a little more 

perceived “weight” in your music. Accessing these settings can even be fully 

automated by means of a home automation controller (Crestron, AMX, Control4, 
etc.) via the RS-232 port on the rear panel of the SC-1.

Disconnect the microphone

Having selected your target curve, it is now time to let MultEQ

®

 Pro do the cal-

culations needed to fully optimize the system in the room. Before you do any-
thing else, however, it is essential to disconnect the measurement microphone 
and reconnect the normal Left channel input. A warning dialog will pop up on 
the PC screen to remind you of this fact.

 

 

Warning!  

You must remove the Calibrated Microphone Preamplifier’s XLR 

connection from the SC-1’s Left input before continuing. Not doing 
this will cause microphone feedback to be played on the system at 
levels that could damage the speakers.

Содержание AUDIO SYSTEM CONTROLLER SC-1





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды