manualshive.com logo in svg

Wisdom AUDIO SYSTEM CONTROLLER SC-1, Руководство пользователя

Поделиться
Скачать
Wisdom AUDIO SYSTEM CONTROLLER SC-1 Скачать руководство пользователя страница 15

15

http://www.markertek.com/Connectors-Adapters/Audio-Adapters/XLR-to-
RCA-Adapters/Switchcraft-Corporation/322X.xhtml

3 

7 Channel Low (Woofer) Output

These seven balanced audio outputs carry the room-corrected “low pass” 

portion of the audio spectrum, and must be connected to the amplifiers 
that drive the woofer sections of the loudspeakers. 

The pin assignments of this XLR-type male output connector are:

2

1

3

 

Pin 1: Chassis ground

 

Pin 2:  (non-inverting)

 

Pin 3: Signal – (inverting)

 

Connector ground lug: chassis ground

These pin assignments are consistent with the standards adopted by the 

Audio Engineering Society, and are used with the purpose-designed SA-

series power amplifiers from Wisdom Audio. If you elect to use a different 
amplifier for your woofers, please refer to the operating manual of your 
power amplifier to verify that the pin assignments of its input connectors 
correspond to your Wisdom Audio SC-1. If not, wire the cables so that the 
appropriate output pin connects to the equivalent input pin, in order to 
preserve the polarity of the musical signal.

Using single-ended amplifiers

If your power amplifier does not have balanced inputs, the adapter used 
to convert from balanced to single-ended must “float” Pin 3 (the inverted 
signal). This can easily be checked with an ohmmeter: the impedance be-
tween Pin 3 and either the center pin or the shield skirt on the RCA should 

be infinite. Tying the output of Pin 3 to ground (as some adapters do) will 
compromise the performance of the SC-1. Should you need them, prop-
erly wired adapters are available from Wisdom Audio for an additional 
charge, or they can be purchased online at 

http://www.markertek.com/Connectors-Adapters/Audio-Adapters/XLR-to-
RCA-Adapters/Switchcraft-Corporation/322X.xhtml.

4 

3 Channel Subwoofer Output

These three balanced audio outputs carry the room-corrected sub-

woofer outputs, and must be connected to the amplifiers that drive the 
subwoofer(s) in the system. 

The pin assignments of this XLR-type male output connector are:

2

1

3

 

Pin 1: Chassis ground

 

Pin 2:  (non-inverting)

 

Pin 3: Signal – (inverting)

 

Connector ground lug: chassis ground

These pin assignments are consistent with the standards adopted by the 

Audio Engineering Society. Refer to the operating manual of your power 

amplifier to verify that the pin assignments of its input connectors cor-
respond to your Wisdom Audio SC-1. If not, wire the cables so that the 
appropriate output pin connects to the equivalent input pin, in order to 

preserve the polarity of the musical signal.

Содержание AUDIO SYSTEM CONTROLLER SC-1





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды