Wireless Solution B-1000, Руководство пользователя

Страница: 4 / 20

DMX Interface
Transceivers on bus: 32 (max)
Data rate: 250 kbps (max)
ESD protection*: ±15 kV
AC input
90-250VAC 50/60Hz
1A at 115VAC (max)
0,5A at 230VAC (max)
DC input
12VDC 1,5A (max)
Compliance declarations
ETSI: EN300 328 & 300 826
EMC: EN301 489-17
CE: EN60950
FCC: UQT-WDXOEMPCBF
IC: 6812A-WDMXOEM
ARIB: 06215559/AA/00
RF characteristics
Output power:
20 25** dBm
100 300** mW
Frequency range:
2402 to 2479 MHz
Channel bandwidth: 1
Sensitivity at 0.1% BER:
-95dBm
* Slewrate limited for
minimum of EMI in unter-
minated networks.
** Only in FCC output
power mode.
Package Contents
In addition to this manual:
1 pc, BlackBox S-1
1 pc, Power cord
1 pc, DC connector
1 pc, Standard antenna
1 pc, Antenna adaptor
2 pc, Trussholder brackets
BlackBox S-1
Transmitter
Installation
1 Attach the antenna to the connector on the front panel. If using
the standard antenna, use also the supplied adaptor.
2 Link the DMX source to the DMX in socket on the rear panel.
3 Connect power to the unit either via the AC power input (90 to
250VAC), the DC power input (12VDC) or via the DMX bypass
RJ45 socket (12VDC). If using the AC input, fit an appropriate
mains plug to the supplied power cord - this should be carried
out only by a qualified electrician .
4 If required, attach the supplied trussholder brackets to the top
cover of the unit (see page 12).
LINK
ON: Normal operation
FLASH: Unlinking all receivers
RAPID FLASH: Linking with receivers
W-DMX
made in sweden
Level
Radio
Batt
Wireless Solution
Sweden AB
FUNCTION
POWER DATA
RX TX
CTRL LINK
S-1
TX
W-DMX
made in sweden
Level
Radio
Batt
Wireless Solution
Sweden AB
FUNCTION
POWER DATA
RX TX
CTRL LINK
RADIO
ON: Indicates that
Level display is
showing signal
strength
BATT
Not used
FUNCTION
Press and release
to search for and
link with receivers
Level
Provides indication
of radio output signal strength
DATA
ON: Transmitting DMX data
RX
&
CTRL
Not used
POWER
ON: Correct power
input present
To add receivers
Note: You can add receivers at any time, even during operation.
1 Power on the receiver unit(s) and ensure that they are not linked
with any other transmitter (
LINK
indicators should be OFF).
2 On the transmitter unit, press and release the
FUNCTION
button.
The transmitter will scan for all unlinked receivers for a
period of ten seconds - the
LINK
indicator will flash rapidly.
3 If successful, each receiver’s
LINK
indicator will go ON. If any
failed, check that the receiver is in range and repeat procedure.
To unlink all receivers
1 On the transmitter, press and hold the
FUNCTION
button until
LINK
begins flashing. All registered receivers will be unlinked.
AC power input
(90-250VAC)
DC power input
(12VDC)
DMX in (RJ45)
1: DMX- 5: n/c
2: DMX+ 6: n/c
3: n/c 7: Signal GND
4: n/c 8: n/c
DMX bypass,
(XLR female 5pin)
Reserved
DMX bypass, DC power in
1: DMX- 5: +12VDC
2: DMX+ 6: n/c
3: n/c 7: Signal GND
4: +12VDC 8: DC GND
DMX in,
(XLR male 5pin)
IMPORTANT
Only one DMX
universe input
may be connected
at any time