Wire Tech WR-1004MLD Скачать руководство пользователя страница 9

Страница: 9 / 12

WR-1004MLD Outdoor Optical Node Operation and Maintenance Manual

- 8 -

8. NMS setup instructions

If users configured the network management responder, need to do the following settings:

Responder IP setup instruction:
Network management directly modify:

Default IP is 192.168.1.168

，

default gateway is 192.168.1.1

，

default subnet mask is

255.255.255.0

Connect the computer and responder (can be direct connected), and change the computer

IP to 192.168.1.XXX (XXX is any number from 0 to 255 except 168); start upper
computer network management software, then search the device and log in.

Right-click device icon and choose modify the device IP.

Enter new IP address, gateway and subnet mask.

Click modify

，

then exit, it is done. There will show new IP address and gateway on

operational logbook.

Reboot the responder, the new IP take effect (Click the reboot button in the network

management software or power on again)

Содержание WR-1004MLD













Результаты поиска

Содержание WR-1004MLD

Отзывы:

Похожие инструкции для WR-1004MLD

Бренды по названию

Популярные бренды

Wire Tech WR-1004MLD, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание WR-1004MLD

Отзывы:

Похожие инструкции для WR-1004MLD

Бренды по названию

Популярные бренды