Wipaire 8750 Скачать руководство пользователя страница 92

Страница: 92 / 104

SERVICE MANUAL & ICA
8750 AMPHIBIAN/SEAPLANE FLOATS ON CESSNA 208/208B

P/N 1005723 Doc. No. W8750-24-01

Page 92 of 104

Revision C

INSP.

MECHANIC

Lt.

Rt.

FLOAT REM

VAL I

STRUCTIO

S/PROCEDURES (CONT.)

THIS IS INTENDED AS A

GENERAL GUIDE. EACH INST

ALLATION MAY HAVE

SUBT

LE DIFFERE

NCES. ALWAYS US

E TH

E INSTALLATION DRAWING

AS THE

FINAL REFERENCE. ALL WORK SHOULD

BE DO

NE BY CERTIFIED AIRCRAF

TECHNICIANS.

(

Remove the following items from aircraft

continued)

Retract cab

le (Secure in main gear well).

Break lines and cap.

Electrical cannon plug in main wheel well.

Steering cables in tail.

Remove ru

dder horn or clamp to main ru

dder cables.

ssemble main gear if needed.

Install nose gear and attach steering bungee.

Assemble support cre

, minimum six (6) crew members.

10.

ith wheels just touching the ground, remove the 4 main gea

r saddles and

upper front attach bolts.

11.

ift aircraft and remove floats.

12.

Lower aircraft positioning main gear assembly for installat

ion.

13.

Torque main gear saddle bolts to 75 ft. lbs.

14.

onnect brake lines a

nd bleed for air bubbles.

15.

Install main gear belly plate and fairings.

16.

emove fro

t strut fittings.

17.

Install pilot

and co-pilot step assemblies.

18.

eplace Passenger Door Cable As

sy. (2) P/N S2837-2 with ori

ginal Cable Assy. (2)

P/N S2837-1

19.

Install tail c

one and tail hatch cover.

20.

Install lower LT. cowling.

21.

Install all n

ose gear fittings.

22.

Install all fl

oor plates and carpet.

23.

Install aft bulkhead.

24.

Install any seats previously removed.

Содержание 8750









































































































Результаты поиска

Содержание 8750

Отзывы:

Wipaire 8750, Руководство по обслуживанию, Страница: 92 / 104

Результаты поиска

Содержание 8750

Отзывы: