Winterthur Gas & Diesel Ltd. X52 Скачать руководство пользователя страница 446 | Manualshive

Страница: 446 / 519

background image

12.3

System oils

System oil has the functions that follow:

•

System oil lubricates the bearings, the running parts of the engine and the crosshead
assemblies.

•

System oil decreases the temperature of the pistons and the vibration dampers.

•

System oil is used as hydraulic fluid in the servo oil system.

12.3.1

Requirements for system oil

The system oil must have the basic properties that follow:

•

An additive-type crankcase oil of SAE 30 viscosity

•

Minimum Base Number (BN) of 5 mg KOH/g

•

Minimum failure load stage of 11 ± 1 related to the FZG gear oil test method A/8.3/90
(ISO 14635-1)

•

Detergency properties

•

Thermal stability

•

Anti-corrosion properties

•

Anti-foam properties

•

Demulsifying performance.

You find a list of applicable and validated system oils in

12.6 List of system oils

.

12.3.2

Recommended procedure for system oil maintenance

WinGD recommends to install a self-cleaning centrifugal separator in the plant oil system. Thus
you can keep the system oil in good condition for a long period.

•

There is always a risk that water, specially sea water, can enter the system oil and cause
corrosion on engine parts. Water contamination can also cause bacterial contamination of
the system oil, which gives a decrease in lubrication performance and gives heavy corrosion
of the engine parts. Thus solid contaminants (dirt) and water must be removed from the
system oil as completely as possible.

•

The self-cleaning centrifugal separator is used as a purifier in bypass mode. The oil flows
from the oil tank through the centrifugal separator. Set the oil flow through the centrifugal
separator related to the manufacturer of the centrifugal separator. WinGD recommends an
oil temperature for this treatment of 95°C unless the manufacturer of the centrifugal
separator recommends differently.

X52

AA00-0000-00AAA-030F-A

Operation Manual

System oils

Winterthur Gas & Diesel Ltd.

- 446 -

Issue 002 2018-11

«
...
444
445
446
447
448
...
»

Содержание X52








































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X52

Бренд: Omnia Страницы: 8

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: XanLite Страницы: 4

Бренд: Major Страницы: 52

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренд: Gait up Страницы: 12

Бренд: Gait up Страницы: 6

Бренд: Gaiam Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды