WinSystems SYS-405 Скачать руководство пользователя страница 6

Страница: 6 / 57

SYS-405/Before You Begin

v1.0

www.winsystems.com

Page 2

2. Before You Begin

Review the warnings (in this section) and the best practice recommendations (see “Best

Practices” on page 49) when using and handling the WinSystems SYS-405. Adherence

to these recommendations provides an optimal user experience and prevents damage.

Read through this document and become familiar with the SYS-405 before proceeding.

2.1 Warnings

Only qualified personnel should configure and install the SYS-405. While observing the

best practices, pay particular attention to the following:

3. Introduction

This manual provides configuration and usage information for the SYS-405. If you still

have questions, contact Technical Support at (817) 274-7553, Monday through Friday,

between 8 AM and 5 PM Central Standard Time (CST).

Refer to the WinSystems website for other accessories (including cable drawings and

pinouts) that can be used with your SYS-405.

4. Functionality

The SYS-405 is a high-performance, industrial, small form factor (SFF) Single Board

Computer (SBC) capable of operating at high temperatures without a fan or heat-pipe.
The processor for the unit is an Intel

E3800 series Atom

™

, integrated into the SYS-405

using a Type 6 COM Express module. The low-profile thermal solution provides a

rugged platform base that protects the PCB assembly and offers convenient four-point

FAILING TO COMPLY WITH THESE BEST PRACTICES MAY DAMAGE THE

SYS-405 AND VOID YOUR WARRANTY.

Avoid Electrostatic Discharge (ESD)

Only handle the circuit board and other bare electronics when electrostatic discharge

(ESD) protection is in place. Having a wrist strap and a fully grounded workstation is

the minimum ESD protection required before the ESD seal on the product bag is

broken.

Warning

Do not reverse the positive and negative terminals when you connect power to the
unit. This will void the warranty and damage the board.

Содержание SYS-405


























































Результаты поиска

Содержание SYS-405

Отзывы:

WinSystems SYS-405, Руководство по эксплуатации продукта, Страница: 6 / 57

Результаты поиска

Содержание SYS-405

Отзывы: