winsonic MFC1705S-EN30C Скачать руководство пользователя | Manualshive

Страница: 30 / 41

background image

Panel Specification

(a) When the module is assembled, it should be attached to the system firmly

using all mounting holes. Be careful not to twist and bend the module.

(b) Because the inverter uses high voltages, it should be disconnected from power

source before it is assembled or disassembled.

(c) Refrain from strong mechanical shock and / or any force to the module.

In addition to damage, it may cause improper operation or damage to the module
and CCFT back light.

(d) Note that polarizer films are very fragile and could be damaged easily.

Do not press or scratch the surface harder than a HB pencil lead.

(e) Wipe off water droplets or oil immediately. If you leave the droplets for a long

time, staining or discoloration may occur.

(f) If the surface of the polarizer is dirty, clean it using absorbent cotton or soft cloth.

(g) Desirable cleaners are water, IPA (Isopropyl Alcohol) or Hexane.

Do not use Ketone type materials (ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid
or Methyl chloride. It might cause permanent damage to the polarizer due to chemical
reaction.

(h) If the liquid crystal material leaks from the panel, it should be kept away

from the eyes or mouth . In case of contact with hands, legs or clothes, it must
be washed away with soap thoroughly.

(i) Protect the Module from static, or the CMOS Gate Array IC would be damaged.

(j) Use finger-stalls with soft gloves in order to keep display clean during the

incoming inspection and assembly process.

(k) Do not disassemble the Module.

(l) Do not pull or fold the lamp wire.

(m) Do not adjust the variable resistor located on the Module.

(n) Protection film for polarizer on the Module should be slowly peeled off just before use

so that the electrostatic charge can be minimized.

(o) Pins of I/F connector should not be touched directly with bare hands.

8. General Precautions

8.1 Handling

«
...
28
29
30
31
32
...
»

Содержание MFC1705S-EN30C










































Отзывы:

Нет отзывов

Похожие инструкции для MFC1705S-EN30C

Бренд: NEC Страницы: 26

SMARTMETER iBloodPressure 2.0

Бренд: A&D Страницы: 32

Бренд: Z Microsystems Страницы: 32

Бренд: Miro Displays Страницы: 35

Бренд: MEE Страницы: 48

Бренд: GERATHERM Страницы: 228

Бренд: AOC Страницы: 1

HeartGuide BO8000-L

Бренд: Omron Страницы: 72

Бренд: Dynascan Страницы: 31

MA504/1 Software S

Бренд: Siko Страницы: 20

Бренд: HANNspree Страницы: 19

Бренд: BELINEA Страницы: 12

Бренд: ABB Страницы: 11

Industrial enabled Analyzer 9437

Бренд: ABB Страницы: 32

Бренд: Kenwood Страницы: 14

Бренд: Kenwood Страницы: 32

Бренд: Kenwood Страницы: 22

Бренд: Kenwood Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды