![background image](http://html1.mh-extra.com/html/winnebago/2003-adventurer/2003-adventurer_owners-manual_987433049.webp)
3-3
SECTION 3
IN CASE OF DRIVING EMERGENCY
be operated without placing your body
beneath vehicle.
2. Screw jack extension pad out (up) until it
touches jacking point surface.
3. Begin jacking until jack is firmly positioned
and just begins to bear weight, but
do not
lift
tire off the ground.
4. “Crack” wheel nuts loose with lug wrench,
but do not unscrew nuts yet.
5. Resume jacking until wheel is free of
ground.
6. Remove wheel nuts and wheel; put spare
wheel in place.
7. Install wheel nuts and tighten as much as
possible with wheel and tire off the ground.
8. Lower tire until tire just contacts the ground.
Tighten nuts with lug wrench in sequence
recommended by chassis manufacturer.
9. Finish lowering jack, then remove jack and
blocks.
DUAL REAR WHEELS
Before trying to remove the rear wheel, follow
safety precautions in the beginning of the motor
home jacking procedures. Then follow the proce-
dure below:
1. Place jack under jacking point specified by
chassis manufacturer. See
Jacking Points
on
previous page. Position jack so it may be
operated without placing your body beneath
vehicle.
2. Screw jack extension pad out (up) until it
touches jacking point surface.
3. Begin jacking until jack is firmly positioned
and just begins to bear weight, but
do not
lift
tire off the ground.
4. “Crack” wheel nuts loose with lug wrench,
but do not unscrew nuts yet.
5. Resume jacking until wheel and tire are free
of ground.
6. Remove wheel nuts and wheel.
NOTE: When installing the outer dual wheel and
tire assembly, rotate the outer dual wheel
so valve stems are accessible but not
touching one another. In some cases this
means that the inner and outer valve
stems should be in separate wheel cutout
locations.
NOTE: When installing or tightening dual
wheels, both wheels on the same side
must be off the ground (not resting on the
inner dual). This minimizes the possibili-
ty of loose wheels after correct mounting
torque is applied.
7. Mount spare wheel on studs and replace
wheel nuts. Refer to your chassis operating
guide for wheel nut torque and tightening
sequence.
WHEEL NUTS
To properly seat the wheel nuts and to elimi-
nate the possibility of the wheel nuts becoming
loosened while driving, they should be tightened
at frequent intervals to the torque specified in
your chassis operating guide. This is especially
important after the first 100, 1,000 and 6,000
miles of operation after replacement of a wheel or
wheel nuts.
RECOVERY TOWING
When calling a professional towing service,
we recommend that you advise them of your
coach length and approximate front axle weight.
This will allow the towing operator to determine
the proper towing equipment to use. (This infor-
mation is found on the vehicle certification label
located to the left of the steering wheel.)
Upon satisfactory completion of
emergency tire change, it is highly
recommended that wheel nuts be
properly torqued and inspected by
qualified service personnel as soon as
possible.
WARNING
DO NOT crawl under the vehicle
when it is supported by a jack.
WARNING
Содержание 2003 adventurer
