![background image](http://html1.mh-extra.com/html/winnebago/2003-adventurer/2003-adventurer_owners-manual_987433033.webp)
2-9
SECTION 2
DRIVING YOUR MOTOR HOME
unit does not have a valid calibration, the
heading and the word ‘CAL’ will flash con-
tinuously.
4. If the temperature reading is valid, the tem-
perature display will remain ‘on’ continu-
ously. If the temperature reading is invalid
(due to an open or shorted temperature sen-
sor), the temperature reading will flash con-
tinuously.
5. Unit goes to SLEEP MODE when ignition is
turned off.
Sleep Mode Operation:
1. Unit enters SLEEP MODE when ignition is
turned off.
2. The display is blank and the unit is in a LOW
POWER MODE.
3. Unit wakes from SLEEP MODE and enters:
A. Ignition ON operation when the ignition
is turned on, or
B. CAMPING MODE when the °F/°C or
the MODE button is pressed for three (3)
seconds.
Camping Mode Operation:
1. Unit enters CAMPING MODE after the °F/
°C button or MODE is pressed for (three) 3
seconds while in SLEEP MODE.
2. Unit displays temperature and heading for
ten (10) seconds; the display stays ‘on’ if
you continue to push either button and then
returns to SLEEP MODE ten (10) seconds
after the last button was pushed.
Nighttime Dimming:
The display brightness is decreased by 50%
when the vehicle head lamps are turned on.
Calibration:
The compass must be calibrated after its ini-
tial installation and anytime the compass sensor
is replaced or relocated. The calibration values
are saved in EPROM memory, so it is not neces-
sary to recalibrate if the battery is disconnected.
Calibration Procedure:
1. Press and hold the MODE button until the
words ‘ZONE’ and ‘CAL’ appear (approxi-
mately ten (10) seconds). The unit will dis-
play the current zone value.
2. Press the °F/°C button to increment the zone
value.
3. Press the MODE button to store the zone
value.
4. The unit now displays the word ‘CAL’. Press
the °F/°C button to enter the calibration
mode. The display will begin counting down
from 60 seconds and the work ‘CAL’ will
flash. The driver should slowly drive in a cir-
cle during the 60 second calibration period.
If the calibration procedure failed, the unit
will flash the word ‘CAL’ continuously. If
the calibration procedure is successful, the
unit will display the work ‘CAL’ for five (5)
seconds and then return to normal ignition
‘on’ operation.
ZONE ADJUSTMENT
When you travel outside the zone, the unit is
currently set ‘on’, the compass has reduced accu-
racy. To achieve maximum accuracy, it is recom-
mended to change the zone setting when
traveling to a new zone in the U.S. To change the
zone setting, follow steps (1.) through (3.) of the
CALIBRATION ROUTINE, at which point the
unit will display the word ‘CAL’. Press the
MODE button again to skip calibrating. It is not
necessary to recalibrate the compass when you
change zones.
Compass zones for the U.S.
Содержание 2003 adventurer
