Winegard TRAV'LER RP-SK01 Series Скачать руководство пользователя страница 4

6. Slide the LNB guard up the feed arm and over the LNB. The front of the LNB 

guard should be ~½” in front of the LNB and should not be touching the LNB. 
Install the four bolts through the four holes in the LNB guard. Thread a nut onto 
each bolt, and tighten. 

RP-SK73 SHAW DIRECT  

LNB REPLACEMENT

1. Remove and set aside the four nuts and bolts 

holding the LNB guard to the feed arm. Then, 
remove the LNB guard from the feed arm.

2. Remove and set aside the screw holding the 

LNB to the feed arm.

3. Disconnect the four coax cables from the LNB 

using a 

7

/

16

” wrench, and carefully remove the 

LNB from the feed arm. 

4. Connect the four cables running through the 

feed arm to the four ports on the replacement LNB. The cables can be connected 
in any order. Tighten each cable until fingertight, and then use a 

7

/

16

” wrench to 

tighten a quarter turn more.

5. Slide the LNB into the feed arm, and re-install the screw (removed earlier) through 

the underside of the feed arm and replacement LNB. Tighten.

6. Slide the LNB guard onto the feed arm and over the LNB. The front of the LNB 

guard should be ~½” in front of the LNB.

7. Install the four bolts through the four holes in the LNB guard. Thread a nut onto 

each bolt, and tighten. 

STOWING THE ANTENNA

1. Plug in the interface box. 

2. Press and hold “POWER” for two seconds to turn on the interface box. Then, 

press the Power button again to stow the antenna.

Four coax cables 

connected to LNB

Bolts holding LNB 
guard to feed arm

Screw holding 

LNB to feed arm

Disclaimer: Although every effort has been made to ensure that the information in this manual is correct and complete, no company 

shall be held liable for any errors or omissions in this manual. Information provided in this manual was accurate at time of printing.

DISH is a registered trademark of DISH Network L.L.C. DIRECTV is a trademark of AT&T Intellectual Property and/or AT&T affiliated 

companies. Shaw Direct is a trademark of Shaw Satellite G.P. TRAV’LER, and Winegard are registered trademarks of Winegard Company. 

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 

 1-800/788-4417 • FAX 319/754-0787 • www.winegard.com • Printed in U.S.A. • ©2012 Winegard Co

                                                                                                                          Rev2 9/18  2452261

Содержание TRAV'LER RP-SK01 Series

Страница 1: ...acement Instructions Models RP SK01 RP SK05 RP SK09 RP SK73 RPSK01H For help email help winegard com or call 1 800 788 4417 www winegard com mobile 2452261 Rev2 9 18 NOTE RPSK01H LNB Replacement is only compatible with SK 1000 built after 1 1 2018 ...

Страница 2: ...pter Disconnect the three cables from the LNB using a 7 16 wrench 3 RP SK01 Connect the three cables running through the integrated adapter to ports 1 3 in any order on the replacement LNB Tighten each cable until fingertight and then use a 7 16 wrench to tighten a quarter turn more RPSK01H Using the supplied dual coax cable connect the ends with red heat shrink wrapping to Port 1 on LNB and Port ...

Страница 3: ...should be in front of the LNB and should not be touching the LNB Install the four bolts through the four holes in the LNB guard Thread a nut onto each bolt and tighten RP SK09 DIRECTV SWM SLIMLINE LNB REPLACEMENT 1 Remove and set aside the four nuts and bolts holding the LNB guard to the feed arm Then slide the LNB guard down the feed arm and toward the reflector 2 Remove and set aside the two scr...

Страница 4: ...n 6 Slide the LNB guard onto the feed arm and over the LNB The front of the LNB guard should be in front of the LNB 7 Install the four bolts through the four holes in the LNB guard Thread a nut onto each bolt and tighten STOWING THE ANTENNA 1 Plug in the interface box 2 Press and hold POWER for two seconds to turn on the interface box Then press the Power button again to stow the antenna Four coax...

Отзывы: