Winegard SENSAR Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 8

Winegard SENSAR Скачать руководство пользователя страница 5

5

WHAT TO DO WHEN YOUR RV/TV ANTENNA IS NOT WORKING PROPERLY

Step 1.

Strip outer cover back 1/2"* from end of cable. Fray braid back as far as outer

cover will allow.

Step 2.

Trim braid close to outer cover and remove 1/4"* of inner insulation

being

careful not to nick center conductor

. Make sure no foil or braid can touch center

conductor.

Step 3.

Slide connector tip between braid and inner insulation (braid and foil, on foil

shield cable) and push connector on cable as far as it will go. Crimp built-in ferrule with
proper crimping tool.

Hex connector requires hex crimping tool

. Do Not crush

cable out-of-round.

*

If installing in very hot weather, increase these dimensions 1/8".

WARNING

Do not install couplers, splitters, etc. between the
power supply and the antenna. Installation of any
item on the downlead may cause a short in the
system. The downlead su12 VDC to the
preamp in the antenna.

Turning power supply on sends +12 VDC up cable
to antenna. Voltage energizes transistors on
amplifier in antenna head. TV signal comes back
down cable to outlets.

TO TEST SYSTEM, Figure 2

1. Make sure TV set is working properly.
2. Switch power supply ON and OFF to difference
in picture quality while watching TV. If NO there is
difference, use following steps.

CAUTION:

The power supply should be turned

OFF when connecting/disconnecting cables to
power supply and antenna, but should be turned
ON when testing for voltage.

3. Disconnect cable from antenna and check for
+12 VDC at Test Point #1. If there is +12 VDC, the
power supply is OK. Replace antenna.
4. If there is NO +12 VDC at Test Point #1,
reconnect cable to antenna. Remove power
supply from wall and visually inspect for burned/
broken parts. If there are ANY broken/burned
parts, replace power supply.
5. Disconnect cable from antenna jack on power
supply. Check for +12 VDC at Test Point 2. If +12
VDC is present, there is a cable problem
connecting the power supply to the antenna.
Repair/replace cable
6. If +12 VDC is not present at Test Point # 2, be
sure the green indicator light is ON. If not, check
the polarity of the red/white wires and the +12
VDC source. If there is still no +12 VDC, replace
power supply.

2ND Set

Hook Up

No +12 VDC
at this point

Set 2

HOW YOUR SYSTEM WORKS, Figure 1

Figure 1

Figure 2

TEST POINT #1

+12 VDC at Antenna

White
GND.

2ND Set

No +12 VDC
at this point

Set 2
Connection

Red
+12 VDC

+12 VDC
at
Antenna
Jack

TEST
POINT #2

INSTALLING F-CONNECTORS ON COAXIAL CABLE

GND.

Antenna
Connection

+12 VDC

Amplified
TV Signal

Red
+12 VDC

White

«
...
3
4
5
6
7
...
»

Содержание SENSAR









Отзывы:

Нет отзывов