background image

3

AMPLIFIED MODELS ONLY

STEP 11:

Select location for wall plate.  Run two

coax cables (RG-59 type) (three if set 2 jack is going
to be used) between locations and install connectors
on each end. 

Mark cables so "cable input", "TV

output" "Set 2" may be identified. 

Antenna

downlead and +12 VDC will also be needed at inside
wall plate/power supply location.

STEP 12:

The wall plate/power supply assembly

may be flush mounted in most standard electrical

boxes. To flush mount cut a hole in wall to fit the box.

Run 2  #12 wires between wall plate/power supply

and +12 VDC source and route downlead cable to

this locatio

n.

CAUTION
THE POWER SUPPLY SHOULD BE TURNED OFF
WHEN CONNECTING CABLES/WIRES TO POWER
SUPPLY.  SEE FIGURE 14.

STEP 13:

Make 12 volt connection to wall plate/

power supply, Figure 10. Install terminals on wires

from +12 VDC source, Figure 11. Crimp terminals

with appropriate crimping tool or equivalent, Figure

12. Push wires onto tabs on terminal board as shown

in Figure 10. If in doubt as to the polarity of the wires,

connect them temporarily to tabs on circuit board and

press ON switch on front of wall plate; if light comes

on, polarity is correct, Figure 10.

STEP 14:

Install connectors on downlead, set 2 and

cable input cables as shown on page 4. Attach

downlead cable to jack on wall plate/power supply

marked antenna, Figure 13. Attach cable going to set

2 outlet to jack on power supply marked SET 2.

Attach cable coming from cable input to jack on

power supply marked CABLE.

STEP 15:

Mount power supply in wall with screws

provided and attach TV set cable to jack on front of

power supply/wall plate.  Press ON switch on front of

wall plate and check that light is on, Figure 14.

CHECKING OPERATION OF POWER SUPPLY

1. Tune TV receiver to nearest station and rotate
antenna for best picture and sound.
2. Press OFF switch on power supply. Picture on TV
should be considerably degraded with power off.
3. 

This unit is equipped with a polyswitch

,

(current limiting device), which will shut down +12
VDC if there is a direct short between antenna and
power supply. Green indicator light will not light.
Once short is eliminated, device will reset itself.

ADDING OPTIONAL AMPLIFIED WALLPLATE TO
NON-AMPLIFIED RV/TV INSTALLATION

Model RA-7596 solid state TV signal amplifier works
with any non-amplified RV/TV antenna. Improves
picture quality. Uses +12 VDC; has on/off switch,
indicator light, set 2 output, cable input and +12 VDC
receptacle.

FIGURE 10

-12 VDC
(Ground)

+12 VDC

FIGURE 12

FIGURE 13

FIGURE 14

WARNING

DO NOT connect high
current devices such as
hair dryers to this
receptacle. Maximum
current rating of this
receptacle is 8 amps at
+12 VDC.

FIGURE 11

Connector
Ferrule

Crimp  Here

1/4"

       #12 Wire

Remove 1/4" of insulation
from #12 wire.

Connector
Insulation

Cable Input

Set 2
Output

Antenna
Downlead

Содержание SENSAR









Отзывы: