background image

Windsor Industries reserves the right to change its warranty policy without notice – Rev2    10/16/02

2

WINDSOR INDUSTRIES

New Machine Warranty

90 Day Warranty Extension Available

Upon receipt of the Machine Registration Card, Windsor will extend by 90 days, from the date of purchase, all items included under
the one-year provision. This applies only to one-year items and does not include 90-day wear items.

This Warranty Shall Not Apply To:

1.

 

Any product that has been subject to abuse, misuse, neglect or unauthorized alteration (including the use of incompatible or
corrosive chemicals or overloading of capacity).

2.

 

Products that have experienced shipping or freight damage.

3.

 

Repairs necessary to correct any failure due to improper pre-delivery service and inspection by the selling dealer.

4.

 

Excessive time for cleaning units in preparation for repair.

5.

 

Any repairs resulting from poor initial service work or improper diagnosis.

6.

 

Tune-up parts such as plugs, plug wires and condensers.

7.

 

Any design alterations performed by an organization not authorized or specified by Windsor.

8.

 

Battery and charger warranties are handled directly with the manufacturer (Trojan

Ò

 batteries and Lester

Ò

 chargers).

9.

 

High-pressure washing.

10.

 

Electrical components exposed to moisture.

If difficulty develops during the warranty period, contact the authorized Windsor agent from whom the product was purchased.
Windsor Industries, Inc. may elect to require the return of components to validate a claim. Any defective part to be returned must be
shipped freight prepaid to an authorized Windsor Distributor/Service Center or to the Windsor factory.

Use Of Parts Not Approved By Windsor Industries, Inc. Will Void All Warranties

This warranty is valid only for all products sold after July 1, 1995. A product sold before that date shall be covered by the limited
warranty in effect at the date of sale to the original purchaser.

Windsor Industries, Inc.  

  a Castle Rock Industries company  

  1351 W. Stanford Ave.  

  (303) 762-1800  

  800-444-7654  

  FAX (303) 865-2800

Содержание LB1500



























Отзывы: