manualshive.com logo in svg

Windsor Chariot 2 iVac 24 AVT, Руководство по эксплуатации, Страница: 38 / 122

Поделиться
Скачать
Windsor Chariot 2 iVac 24 AVT Скачать руководство пользователя страница 38

38

Maintenance

Do not use a pressure washer to clean around the 
brush motors. Use tap pressure only.

N’utilisez pas de nettoyeur haute pression pour 
nettoyer autour des moteurs des brosses. Utilisez 
seulement la pression du robinet.

Remove Brush Deck

1. Lower brush deck.

2. Turn off machine

3. Disconnect motor harness connectors and remove 

vacuum hose from top of deck.

4. Remove bumper bolts and bumper to access 

linkage mount brackets.

5. Pull down and disconnect spring mount bracket 

from deck lift arm. Keep spring attached to mount 
bracket.

6. Remove four (4) bolts and associated hardware 

that connect deck lift arm to linkage mount 
brackets on drive assembly.

7. Remove two (2) bolts and associated hardware 

that connect deck lift arm to lift linkage plate.

8. Pull out deck with attached deck lift arm.

9. Reverse to reassemble.

Replace Brush Deck Motor

1. Remove brush deck from machine.

2. Remove two (2) nuts to free rear mounting bracket 

from deck.

3. Remove six (6) motor mount bracket face screws.

4. Remove rear mounting bracket.

5. Remove motor with attached coupler, leaving front 

motor mounting bracket still attached to deck.

6. Remove coupler from old motor for reuse.

7. Inspect spider coupler for wear replace as needed.

Reverse process to reassemble with new motor.

Brush Motor Carbon Brush Replacement

1. Scribe alignment mark on motor barrel to motor 

cap. Remove two bolts.

2. Remove end cap from motor.

NOTE: Motors contain two wave washers in cap. Do 
not lose these.

3. Release brush from spring tension. Remove screw 

connecting brush wire lead to brush holder. Clean 
brush holder to insure free movement.

4. Retract spring and install new brush. Install 

connector screw and lead.

5. When all new brushes are installed. Place all in 

retracted position, held into brush holder by spring 
tension.

6. Carefully place end cap onto bearing on motor 

shaft. 

NOTE: Use care to assure wave washer alignment.

7. With end cap in partially installed position, release 

all brushes to contact position with motor commu-
tator.

NOTE: Failure to insure all brushes are released will 
result in motor failure.

8. Reset end cap and realign with scribe marks on 

motor barrel. Reinstall the two attach bolts from 
cap into base.Maintain alignment between motor 
barrel base and cap. 

FOR SAFETY:

 before leaving or servicing machine, 

stop on a level surface, turn off machine and discon-
nect powe

r.

Replacing Coupler Spider

1. Remove three (3) cover screws and drive housing 

cover from end of brush deck.

2. Remove four (4) drive housing mounting screws 

3. Slide out brush drive housing assembly with 

attached coupler from end of brush deck extrusion.

4. Replace coupler spider.

5. Reverse to assemble.

NOTE: Align coupler jaws when sliding in brush drive 
housing assembly.

86374850 Chariot iVac 24

Содержание Chariot 2 iVac 24 AVT



























































































































Отзывы:

Нет отзывов