background image

32

Guarantee and warranty limitations

Subject to tec

hnical modifications. 

A

WÖ– v

o

r-07/20

08

The guarantee and warranty limitations require that the boiler and related accessories be properly installed and
started up by WINDHAGER Customer Service or Customer Service PARTNER; otherwise the manufacturer’s guar-
antee will not be honoured. 

Malfunctions resulting from improper operation or adjustment as well as use of poor or not recommended fuel
types are not covered by the guarantee and warranty. Further, the warranty shall be void if equipment other
than those provided by WINDHAGER are installed. The special warranty restrictions for your system are avail-
able in the “Warranty Conditions” folder supplied with your boiler. 

Start-up and regular maintenance following the terms of the “Warranty Conditions” will assure safe,
environmentally friendly and economical operation of your system. We recommend that you obtain a
maintenance service contract.

Contacts

Regional customer service
Salzburg:

Upper Austria:

Tyrol, Vorarlberg:

Carinthia:

Tel. +43 (0) 62 12/23 41-267

Tel. +43 (0) 62 12/23 41-266

Tel. +43 (0) 62 12/23 41-263

Tel. +43 (0) 62 12/23 41-269

Fax +43 (0) 62 12/45 04

Fax +43 (0) 62 12/45 04

Fax +43 (0) 62 12/45 04

Fax +43 (0) 62 12/45 04

Vienna, Lower Austria, Burgenland:

Styria:

Tel. +43 (0) 1/869 43 28-340 or 01/869 43 28-450

Tel. +43 (0) 1/869 43 28-670

Fax +43 (0) 1/865 13 81

Fax +43 (0) 1/865 13 81

E-mail: [email protected]

Technical assistance:

Tel: +43 (0) 62 12/23 41-238
Fax +43 (0) 62 12/23 41-259

Headquarters:
Windhager Zentralheizung GmbH
A-5201 Seekirchen

Anton-Windhager-Str. 20
Tel. +43 (0) 62 12/23 41-0
Fax +43 (0) 62 12/42 28
E-mail: [email protected]

Spare parts:

Tel. +43 (0) 62 12/23 41-268
Fax +43 (0) 62 12/42 26

Windhager Zentralheizung GmbH
D-86405 Meitingen

Deutzring 2
Tel. +49 (0) 82 71/80 56-0
Fax +49 (0) 82 71/80 56-30
Spare parts: Tel. +49 (0) 82 71/80 56-600
E-mail: [email protected]

Customer service, western and southern Germany:

Tel. +49 (0) 82 71/80 56-700
E-mail: [email protected]

Windhager Zentralheizung Schweiz AG
CH-6203 Sempach-Station

Industriestrasse 13
Tel. +41 (0) 41/46 94 69-0
Fax +41 (0) 41/46 94 69-9
Spare parts: +41 (0) 41/46 94 69-0
E-mail: [email protected]

Regional customer service
for German-speaking Switzerland:

Tel. +41 (0) 41/46 94 69-6
E-mail: [email protected]

Windhager Zentralheizung GmbH
D-04509 Delitzsch

Heinrich-Rudolf-Hertz-Str. 2
Tel. +49 (0) 3 42 02/7 23-0
Fax +49 (0) 3 42 02/7 23-30
Spare parts: Tel. +49 (0) 3 42 02/7 23-600
E-mail: [email protected]

Customer service, northern and eastern Germany:

Tel. +49 (0) 3 42 02/7 23-700
E-mail: [email protected] 

Switzerland:

Italy:

Germany:

Austria:

Windhager Zentralheizung GmbH
D-49143 Bissendorf

Gewerbepark 18
Tel. +49 (0) 54 02/70 140-0
Fax +49 (0) 54 02/70 140-9
E-mail: [email protected]

Windhager Italia S.R.L.
Via Ungheresca sud
I-331010 Mareno Di Piave (TV)

Tel. +39 /0438/499143
Fax +39 /0438/497884
E-mail: [email protected]

Содержание LogWIN LWP 180

































Отзывы: