background image

EXHAUST OF BLUE SMOKE

CAUSE

SOLUTION

There is machine oil, in cylinder.

Check oil level, drain away the unnecessary machine oil.

Piston, ring is clipped or worn, and
its   springiness   is   not   enough   or
each gap of ring turns to same di-
rection to make the machine oil go
up.

Check, change the piston ring, and cross each gap position.

The gap is too big between piston
and cylinder.

Remedy or change.

Valve and guide are worn.

Change.

EXHAUST OF WHITE SMOKE

CAUSE

SOLUTION

There is water in diesel fuel.

Clean the fuel tank and diesel filter, change diesel fuel.

OTHER POSSIBLE PROBLEMS

CAUSE

SOLUTION

Speed is sometimes high, someti-
mes low.

Check the speed governor system whether it is nimble. Whether
there is air in fuel pipeline.

Abnormal   sound   suddenly   ap-
pears.

Check each motional part carefully.

Exhaust   with   black   smoke   sud-
denly.

Check fuel system, especially nozzle.

There   is   metal   knocking   sound
rhythmically in the cylinder.

The fuel delivery angle is too big. Adjust it.

WIRING DIAGRAM

© by WilTec Wildanger Technik GmbH 

Seite 23 

http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Содержание C173F

























Отзывы: