background image

 

 

Safety Rules and General Warnings 

DO NOT OPERATE THIS FURNACE WITHOUT FRONT PANEL INSTALLED 

 

Due to high temperatures, the furnace should be 
located out of traffic and away from combustible 
materials such as furniture and draperies. 

 

Children and adults should be alerted to the 
hazards of high surface temperatures and should 
stay away to avoid burns or clothing ignition. 

 

Young children should be carefully supervised 
when they are in the same room as the furnace. 

 

Clothing or other flammable material should not be 
placed on or near the furnace. 

 

Any safety screen or guard removed for servicing 
an furnace must be replaced prior to operating the 
furnace. 

 

Keep burner and control compartment clean. 

 

The outside vent cap is hot while furnace is in 
operation. 

 

Installation and repair should be done by a 
QUALIFIED SERVICE TECHNICIAN. The furnace 
should be inspected before use and at least 
annually by a qualified service technician. 

 

More frequent cleaning may be required due to excessive 
lint from carpeting, bedding materials, etc.  It is imperative 
that control compartments, burners and circulating air 
passageways of the furnace be kept clean. 

 

DO NOT put anything around the furnace that will obstruct 
the flow of combustion and ventilation air. 

 

DO keep the furnace area clear and free from combustible 
materials, gasoline and other flammable vapors and 
liquids. 

 

DO examine venting system periodically and replace 
damaged parts. 

 

DO examine burner periodically. Clean and replace 
damaged parts. 

 

DO NOT use this furnace if any part has been under 
water.  Immediately call a qualified service technician to 
inspect the furnace and to replace any part of the control 
system and any gas control which has been under water. 

 

 

Safety Information for Users of LP Gas 

 

Propane (LP Gas) is a flammable  gas which can cause fires and explosions. In its natural state, propane is odorless and 
colorless. You may not know all the following safety precautions which can protect both you and your family from an accident. 
Read them carefully now, then review them point by point with the members of your household.   Someday, when there may not 
be a minute to lose, everyone’s safety will depend on knowing exactly what to do. If, after reading the following information, you 
feel you still need more information, please contact your gas supplier. 

 

 

LP Gas Warning Odor 

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP Gas. 

That’s your signal to go into immediate action! 

 

 

Do not operate electric switches, light matches or use your phone.  Do not do anything that could ignite the gas. 

 

IMMEDIATELY get everyone out of the building, vehicle, trailer or area.  

 

Close all gas tank or cylinder supply valves. 

 

LP Gas is heavier than air and may settle in low areas such as basements. When you have reason to suspect a gas      
leak, keep out of basements and other low areas. Stay out until firefighters declare them to be safe. 

 

Use your neighbor's phone and call a trained LP Gas service technician and the fire department. Even though you may        
not continue to smell gas, do not turn on the gas again.  Do not re-enter the building, vehicle, trailer or the area. 

 

Have the service technician or fire department air out the area before you return. A properly trained LP Gas service 
technician must repair the leak, check and relight the gas furnace for you.

 

 

Содержание 2903511

























Отзывы: