Williams Sound SoundPlus Infrared Receiver WIR RX3 Скачать руководство пользователя страница 12

Receiver Model WIR RX4 

The RX4 is a headset-style receiver. Make sure the 
“eye” on top of the receiver is not covered up when 
in use. 

Step 1: 

Battery Installation: Open the battery 
compartment by sliding the battery door 
open on the earpiece. Press two AAA 
batteries into place, observing proper 
battery polarity. Slide the battery door 
closed, taking care not to crush the plastic 
locking tabs. 

Step 2: 

Turn the power switch on top of the 
receiver on. Adjust the volume control 
wheel located on the bottom of the 
headset. 

Battery Information for Receivers 

For the RX3 Receiver in normal use, a heavy-duty 9 
Volt battery such as the Eveready 216 will last about 
10 hours. Alkaline batteries such as the Eveready 
522 will provide about 17 hours of use. For the RX4, 
alkaline AAA batteries will last about 20 hours. If 
the sound becomes weak or distorted, replace the 
battery. The indicator light may still  be on, even 
with a battery that is weak. Do not leave dead 
batteries in the receivers, they may leak and damage 
the receiver. 

Rechargeable Batteries: 

The RX3 receivers can also use a rechargeable 
battery. We recommend only the 7-cell, 8.4 Volt 
types 

(BAT 003). A fully-charged battery (Williams BAT 
003) will provide about 5 hours of use per charge. 
The battery may be recharged without removing it 
from the receiver. 

The BAT 005 Single Charger has a cord that plugs 
into the receiver “EAR” jack to charge the battery. 
The CHG 1269 Multiple Charger can charge 12 
receivers simultaneously through the receiver “EAR” 
jacks. 

The receiver should always be turned OFF while 
charging. It takes about 14 hours to fully charge the 
battery.  If the battery is providing very short service 
life (under 1 hour of use) let it drain completely by 

leaving the receiver on for several hours and then 
immediately recharge it. 

Receivers can be left charging continuously when 
not in use. 

DO NOT ATTEMPT TO RECHARGE DISPOSABLE 
BATTERIES! 

AVOID SHORTING PLUS AND MINUS BATTERY 
TERMINALS TOGETHER WITH METAL OBJECTS. 
BATTERY DAMAGE AND BURNS CAN RESULT! 

DO NOT MIX RECHARGEABLE BATTERIES & 
CHARGERS FROM DIFFERENT 
MANUFACTURERS. 

Williams Sound 

®

Helping People Hear

13 

Содержание SoundPlus Infrared Receiver WIR RX3
















Отзывы: