background image

Infrared Emitter, Model TX6 

Dimensions, Weight: 

11.125" (28.3 cm) W  x  8.125" (20.6 cm) H x 3.25" (8.3 cm) D, 3.25 lbs. (1.6 kg) 

Color: 

Black epoxy paint with white legends, red acrylic window 

Wall Mount: 

Omnidirectional mount included for wall and ceiling mounting. 

Tripod Mount: 

Optional SS-2 Tripod Stand Kit available 

Power: 

External power supply, 24 VAC, 50 or 60 Hz, 50 VA, 0.9 A nom. current drain 
Transmitter shuts off when baseband signal is not present 

Operating Req.: 

0-50° C ambient temperature, non-condensing, non-corrosive atmosphere 

Coverage Area: 

Single-channel mode: 10,000 sq. ft. (930 sq. m); Two-channel mode: 5,000 sq. ft. (465 sq. 
m) 
50° cone pattern, see coverage diagram 

Front Panel: 

Power Indicator: 

Red LED, visible in lower front of window 

Baseband Indicator: 

Red LED, visible in upper part of window 

Rear Panel: 

Mounting Holes: 

One set of threaded holes for use with omnidirectional mount (included) 
Two threaded holes on sides of the cabinet for Tripod Stand Kit 

Baseband Input: 

BNC connector, 50 

½

, 50 kHz to 1 MHz carriers, 100 mV nominal per carrier, 

10 V RMS maximum aggregate baseband amplitude 

Baseband Output: 

BNC connector, 50 

½

, 50 kHz to 1 MHz baseband 

Power Connection: 

3-pin molex 

Baseband Cable: 

RG-58 Coax, BNC-connectors 

Power Cable: 

NEC Class 2 wiring, 2-conductor, 18 ga.; 200 foot (61 m) max. length (for 18 ga. wire) 
Wire Gauge Options:  22 ga.: 0–10'; 20 ga.: 0–75'; 18 ga.: 0–200' 
Each TX6 Transmitter requires its own 24 VAC Power Supply 

Two–Channel Infrared Receiver, Model WIR RX5 

Size and Weight: 

3-5/8" L x 2-3/8" W x 7/8" H (9.2 cm x 6 cm x 2.2 cm) 

Color and Material: 

Gray, shatter-proof polypropylene 

Battery Type: 

1.5 V (AA) x 2, Alkaline (BAT 001) or Rechargeable AA Ni-Cad (BAT 026) 

Battery Life: 

30 hours with BAT 001, 15 hours/charge with BAT 026, 25 mA, nom. current drain 

Modulation Frequencies: 

95 kHz FM, 50 µS de-emphasis OR 250 kHz FM, 50 µS de-emphasis 

Signal to Noise Ratio: 

60 dB with WIR TX6 

Controls: 

Combination volume/On-Off knob, Push–button channel selector, Slide switch tone con-
trol 

Audio Output: 

3.5 mm mono mini phone jack, maximum into 16 

½ 

Acoustic Output: 

130 dB MAX SSPL90 with EAR 013 

The RX5 Two-Channel Infrared Receiver can be used with a Neckloop TeleCoil Coupler 
(NKL 001) to magnetically couple into a hearing aid that has a telephone pick-up coil. 

Stereo Infrared Receiver, Model WIR RX6 

Size and Weight: 

3-5/8" L x 2-3/8" W x 7/8" H (9.2 cm x 6 cm x 2.2 cm) 

Color and Material: 

Gray, shatter-proof polypropylene 

Battery Type: 

1.5V (AA) x 2, Alkaline (BAT 001) or Rechargeable AA Ni-Cad (BAT 026) 

Battery Life: 

30 hours with BAT 001, 15 hours/charge with BAT 026, 25 mA, nom. current drain 

Modulation Frequencies: 

95 kHz FM, 50 µS de-emphasis AND 250 kHz FM, 50 µS de-emphasis 

Signal to Noise Ratio: 

60 dB with WIR TX6 

Controls: 

Combination volume/On-Off knob, Slide switch tone control 

Audio Output: 

3.5 mm stereo mini phone jack, maximum into 16 

½ 

Williams Sound Corp.

10321 West 70th St., Eden Prairie, MN 55344-3446

U.S.A.  800-843-3544 / 952-943-2252 / FAX: 952-943-2174

© 1996, Williams Sound Corp.  MAN 064B 

Содержание MOD 112




















Отзывы: