2
Wichtig: Nach Beendigung des Heizens den Brennerschieber, während er noch
warm ist, also vor dem Abkühlen/Erkalten aus der Führung herausnehmen.
Sonst kann sich der Schieber durch das Verkleben von Brennrückständen festklem-
men. Sollte der Brennerschieber einmal festsitzen, kann man diesen dann durch ein
leichtes Verkanten nach links/rechts lösen.
Achtung:
Die Befeuerung mit Trockenbrennstofftabletten erfordert viel
Sauerstoff.
Eine gute Belüftung des Zimmers ist daher notwendig!
Tabletten, die nicht restlos abgebrannt sind, wegen der auftretenden Ge-
ruchsbelästigung nicht ausblasen, sondern unbedingt ausbrennen lassen.
Falls nicht genügend Wasser im Kessel ist, sollte der Brennerschieber
auf eine feuerfesten Unterlage gelegt werden und hier die Brennstofftab-
letten restlos abbrennen lassen.
15. Das Dampfabsperrventil bei sichtbarer Dampfentwicklung durch eine Drehung
nach links öffnen. Das Schwungrad von Hand anwerfen, damit das in der Dampflei-
tung und dem Zylinder befindliche Kondenswasser entweichen kann. Dadurch setzt
sich die Dampfmaschine in Betrieb. Die Drehzahl des Schwungrades kann durch das
Dampfabsperrventil geregelt werden.
16. Der Kondenswasserbehälter muss während des Dampfbetriebes
mehrfach ent-
leert werden.
Hierzu vorher das Dampfabsperrventil schließen und die Dampfma-
schine stoppen.
17. Nach Beendigung des Dampfbetriebes und dem Abkühlen sollte die Dampfma-
schine gewartet werden. Noch im Kessel vorhandenes Wasser sollte ausgeschüttet
werden. Hierzu das Federsicherheitsventil abschrauben und vor dem Umkippen des
Modells alle losen aufgesetzten Teile abnehmen.
Vorsicht bei heißem Wasser!
Im
Kessel verbleibendes Wasser kann der Funktion nicht schaden, aber evtl. zu Ablage-
rungen an dem Schauglas führen. Kalkrückstände am Wasserstandsschauglas oder im
Kessel
auf keinen Fall mit Essig oder sonstigen stark ätzenden Mitteln entfernen
(Empfehlung: Verwendung eines kalklösenden Mittels, welches Messing und Lötzinn
nicht angreift). Eine Rußbildung an der Unterseite des Kessels beeinflusst ebenfalls
nicht die Funktion und kann mit einer Bürste entfernt werden. Zum Abschluss das
Modell trockenputzen.
Garantie:
18. Alle WILESCO-Dampfmodelle durchlaufen eine Endkontrolle. Bei einem evt.
Fehler können Sie die Dampfmaschine über Ihren Fachhändler oder direkt an uns ein-
senden.
Wir bitten um Verständnis, dass bereits angeheizte/gebrauchte Modelle
nicht gegen neue ausgetauscht werden können.
Die häufigsten Reklamationen sind
undichte Dampfkessel. Die Lötnaht wird durch Beheizung ohne ausreichenden Was-
serstand zerstört. In solchen Fällen verflüssigt sich das Lötzinn an der Lötnaht trop-
fenförmig und der Kessel wird undicht. Dies ist ein eindeutiger Beweis, dass der Kes-
sel trockenbeheizt wurde.
Bitte beobachten Sie stets sorgfältig den Wasserstand,
da eine Trockenbeheizung jegliche Garantieansprüche ausschließt.
Umweltschutz wird auch bei uns groß geschrieben. Somit haben Sie die Möglichkeit
nach einem langen Dampfmaschinenleben diese und auch die Original-Verpackung
an uns zurückzugeben. (Versandkosten werden nicht übernommen.) Alle zurückge-
sandten Modelle / Verpackungen werden von uns einem fachgerechten Recycling zu-
geführt.
Dieses Modell ist ausschließlich für die oben beschriebene Funktion bestimmt.
Technische Änderungen behalten wir uns vor.
WILESCO wünscht Ihnen nun viel Spaß mit Ihrer Dampfmaschine und
„
Volldampf
voraus
„
!
Attention! Before operating this steam engine model
please read and observe thoroughly the operation
instructions.
Important
information
and
safety
precautions for your own safety:
1.
For safety reasons, children should run the steam
engine only under supervision of adults (recommended
age: from 8 years on, not recommended for children
under 36 months)
. During the operation of the steam model until its complete
cooling the engine must be under constant observation.
2. Each irregularity during operation has to be repaired by a competent and
authorized person or by WILESCO themselves. Otherwise any warranty expires.
3. Any unauthorized change, repair or manipulation to the standard specification will
also invalidate the warranty.
4. All parts which are under steam pressure so as boiler, spring loaded safety valve
etc. leave our works only after a 100% examination. The spring loaded safety valve
must not be manipulated.
The operation of the steam engine without any spring
loaded safety valve is not allowed
The function of the spring loaded valve has to be
checked before each operation by pressing the spring or by a small pull on the upper
valve rod. If lime residues caused by hard water are visible on the spring loaded
safety valve, it has to be replaced immediately.
5.
High temperatures:
The principles on which the engine works mean that the
burner slide, boiler, boiler house, the spring loaded safety valve, the steam pipes etc.
become very hot. Do not touch in order to avoid the risk of burns.
6.
Safety precautions:
During operation, take care that children do not touch any of
the moving parts.
7.
Danger if the boiler is heated without enough water!
Always ensure
that there is enough water in the boiler of the steam engine. Caution:
When refilling WiTabs dry fuel tablets also refill up to the max. level..
The water must always be visible at least at the lower end of the sight
glass
, otherwise the joints become leaking and the boiler will be
destroyed. Any resulting claim, damage or consequential damage cannot be accepted.
If the boiler or any steam leading part leak, stop the steam model immediately by
removing the burner slide. Any necessary repair should be carried out by authorized
staff or at the WILESCO company.
8. The steam engine meets all safety standards and actual regulations. Each boiler has
been submitted to a bursting pressure and water test of 5 bar. The operating pressure
is maximally 1,5 bar.
9.
Imperatively keep the operating instructions with your steam engine.
10. We advise you to place the stationary steam engine on a non sliding surface or fix
it onto a coated chipboard (approx. 16 mm thick) with 4 woodscrews (3,4 x 45 mm).
The size of the board depends on how many models will be run with the steam
engine.
Caution: Don't operate the steam model near flammable objects or on tempera-
ture-sensitive surfaces. Operation only under windless condition.
Operating instructions
11. Filling with water at the first operation and after cooling of the boiler: Unscrew
the spring loaded safety valve and fill the boiler with the funnel up to the water level
maximum (upper end of the sight glass), if possible with warm water. Lift the funnel
slightly during filling so that the air inside the boiler can escape. Use only deficient in
lime water or, even better, water without any lime (e.g. distilled water). Then refit the
spring-loaded safety valve.
12. Screw the steam whistle onto the boiler. Do use only the spanner provided with
the engine. Do not tighten by turning the lever as this will be damaged. When
screwing in the steam whistle, the lever with the chain should point outwards (use
washers if necessary) so that the chain which operates the whistle does not come in
contact with the boiler. Pull the chain gently to operate the whistle.
Note: The steam
whistle can be used to check any overpressure in the boiler.
Assemble the smoke
stack with the enclosed screws on the back side of the boiler house.
13. Before you oil the cylinder,
turn off the steam supply valve
. Then turn off the
oil filler screw and fill in with WILESCO steam oil (item n° Z 83) while turning the
flywheel several times so that the oil is drawn in. Oil again when you refill dry fuel
tablets so that the piston does not seize (2-3 drops of oil are sufficient for an
operating time of abt. 10 minutes).
Keep the steam supply valve closed during the
oiling procedure.
Oil lightly all of the bearings and linkages. Before refilling the
boiler with water, check by operating the steam whistle that no steam pressure is in
the boiler.
14. Place 2 1/2 WiTabs dry fuel tablets upright into the burner slide (not
more than 2 1/2 pcs.) and light them. Use only the original WILESCO
burner slide.
Caution: because of the risk of danger from an open
flame, always take the necessary safety precautions.
The burner slide
is adjustable. The oxygen supply and the flame height can be adjusted
by moving the burner slide in relation to the air holes of the burner slide
guide in the boiler house. Before adding new fuel tablets, always check the water
level and refill the boiler with water to ensure that the boiler does not run dry. The
ratio of fuel tablets to the quantity of water in the boiler is designed so that the boiler
cannot run dry without any added fuel tablets.
The burner slide must be completely
pushed in. Important: After the heating process, remove the burner slide from
the guide whilst it is still hot,
otherwise unburnt fuel may cause the slide to stick. If
the slide becomes stuck, it can be removed by tilting it slightly to the left or right.
Caution:
In order to burn properly, WiTabs dry fuel tablets require a lot
of oxygen
That is the reason why during indoor use the room
should be well ventilated.
To prevent unpleasant smells, the fuel
tablets should burn out - they should not be blown out. If there is not
enough water in the boiler, place the burner slide on a fireproof plate
until the tablets have completely burnt out
15. When steam appears, turn once the steam supply valve to the left to open it. Then
turn the flywheel by hand to let the condensation in the pipes and the cylinder escape.
Then the steam engine will start to operate. The speed of the flywheel can be adjusted
through the steam supply valve.
16. The condensed water tray must be
emptied several times
while the steam engine
is running. Before you empty the condensed water trray, turn off the steam supply
valve and stop the steam engine.
17. After the operation of the steam engine and its cooling, the engine should be
serviced. Pour out the water left in the boiler. For this, unscrew the spring loaded
safety valve and remove all loose parts before turning the engine upside down .
Be
very careful if the water is still hot!
Any water left in the boiler cannot do any harm
but might leave deposits on the sight glass. Any lime formation on the sight glass or
inside the boiler must not be removed by using vinegar or corrosive agent
(advice:
use a lime dissolving agent which does not attack the brass and the solder)
. The
building of soot on the bottom side of the boiler does not influence the function and
can be removed with a brush. Finally, dry the model with a clean cloth.
Warranty:
18. All WILESCO steam engines are carefully checked before leaving the factory.
However, if a problem arises, you can return the steam engine to a specialized
distributor or directly to WILESCO.
We are sure you will understand that models
which had already been fired or used cannot be replaced by new ones.
The most
frequent claims are leaking boilers. The solder will be destroyed if there is not enough
water in the boiler. In this case the solder liquefies drop-shaped and the boiler
becomes leaking. This is an obvious proof that the boiler was fired without enough
water.
Please watch always carefully the water level, because the heating
without enough water excludes any warranty claim.
This steam engine is exclusively meant for the above described function.
Subject to technical change without prior notice.
WILESCO wishes you a good time with your steam engine and
„
full steam ahead
“
!
Attention ! Avant la mise en marche de ce modèle d'une
machine à vapeur veuillez lire et respecter ce mode
d'emploi soigneusement. Remarques importantes et
mesures à observer pour votre sécurité.
1.
Pour des raisons de sécurité, les enfants doivent utiliser la machine à vapeur
uniquement sous la surveillance d'un adulte (âge conseillé : à partir de 8 ans,
non pas recommandé pour enfants en dessous de 36 mois).
Au cours de son
fonctionnement et jusqu
’
à son refroidissement complet, la machine à vapeur doit être
constamment sous surveillance.
2. Tout déaut de fonctionnement de la machie à vapeur doit être réparé par un
détaillant agréé ou par la socité WILESCO ell
3. Toute modification, réparation ou manipulation de la machine à vapeur non prévue
