background image

Initially Issued: 6/22/1995 

Authorization No.: 833 

This Is To Certify That 

Wilden Pump & Engineering LLC 

22069 Van Buren Street, Grand Terrace, CA 92313-5651

Is hereby authorized to continue to apply the 3-A Symbol to the models of equipment, 
conforming to 3-A Sanitary Standards for: 

Diaphragm Pumps, Number: 44-03, set forth below: 

Model Designations: See Attached List 

Valid through: December 31, 2010 

Timothy R. Rugh

_______________________

Executive Director, 3-A Sanitary Standards, Inc. 

*****

The issuance of this authorization for the use of the 3-A Symbol is based upon the 
voluntary certification, by the applicant for it, that the equipment listed above complies 
fully with the 3-A Sanitary Standards designated.  Legal responsibility for compliance is 
solely that of the holder of this Certificate of Authorization, and 3-A Sanitary Standards, 
Inc. does not warrant that the holder of an authorization at all times complies with the 
provisions of the said 3-A Sanitary Standards.  This in no way affects the responsibility 
of 3-A Sanitary Standards, Inc. to take appropriate action in such cases in which evidence 
of nonconformance has been established. 

Next TPV Inspection/Report due: January 2014 

R

Содержание PX4 series












































Отзывы: