ø12 m
ø6 m
77mm
90mm
95mm
5mm
ø8 m
50 m
2
ø2,7 m
5,5 m
2
ø5,4 m
23 m
2
2,5
m
0,8
m
3
m
ø6 m
28 m
2
ø12 m
113 m
2
Test-mode (
gesis
®
P MS8-360-1L...)
After the installation of the sensor it can be checked if the chosen position is optimal
for the sensor. Therefore the sensor is set to test-mode. The time delay is shor-
tened to 2 seconds and the switched-off brightness threshold allows a simple test.
For activating the test-mode the remote control
gesis
®
PIR IR B-21 IPD
is used.
Proceed as following:
−
press
[
]
key on the remote for 4 seconds. If the LED on the sensor is
flashing red/green, the sensor is in test-mode.
−
press
[
]
shortly to quit test-mode. The LED switches off.
Semi- or automatic-mode
(all master
gesis
®
P MS8-360-1L...)
Semi-automatic:
Manually turn on and automatically turn off. For switch-on the remote control
gesis
®
PIR IR B-04 IPD
is necessary.
Fully automatic (default setting):
Automatic switch-on and -off. The brightness threshold is considered on automatic
switch-on. Regardless of the brightness value the following settings can be set via
remote
gesis
®
PIR IR B04 IPD:
−
Switch-off delay is considered
−
Sensitivity of each sensor is considered
−
Remote control can be used in both modes
For setting semi- or automatic-mode use remote
gesis
®
PIR IR B21 IPD.
For
setting the mode with the remote control proceed as following:
1. Press
[
]
briefly. The green LED on the sensor flashes for confirmation.
2. Press
[ZONE 1]
briefly. The green LED on the sensor switches off briefly. The
presence detector is now set in programming function for the operating mode.
3. Press
[ON / OFF]
briefly to switch between semi- or automatic mode
3.1 green LED switches off briefly = semi automatic mode
3.2 red LED flashes briefly = full automatic mode
4. Press
[
]
shortly to save the setting. All LEDs on the sensor switch off.
Setting brightness threshold
(all Master
gesis
®
P MS8-360-1L)
If the light intensity is below the parameterized threshold in automatic mode the
lighting is switched-on, when a movement is detected. If the measured light inten-
sity is above the threshold, the lighting won‘t be switched on in automatic mode.
The lighting can always be switched on via remote control
gesis
®
PIR IR B-04 IPD
,
regardless of the operating mode.
The threshold can be adjusted to the preset values 100, 250, 400, 600, 800 and
1000 Lux (default setting 200 Lux). These values can be increased or decreased in
steps of 50 lux in a range between 50 or 500 lux. For values above 500 lux the fix
values are available.
For setting the threshold the remote control
gesis
®
PIR IR B-21 IPD
is used.
Proceed as following:
1. Press
[
]
shortly. The green LED flashes on the sensor.
2. Press
[xxx LUX]
briefly. Green LED on the sensor switches off briefly and the
corresponding value is set. If this value is correct already complete with 4.
3. Press
[
]
to increase or
[
]
to decrease value in steps of 50 lux. Green LED on
the sensor switches off briefly to confirm action. If red LED flashes briefly, the
minimum of 50 lux or the maximum of 1000 lux is reached.
4. Press
[
]
briefly to save the settings. All LEDs on the sensor turn off.
Switch-ON/-OFF delay time
(all Master
gesis
®
P MS8-360-1L...)
How long the light stays switched-on after detection of the last movement can be
adjusted between 15 and 180 minutes. To set the switch-ON/-OFF time the remote
control
gesis
®
PIR IR B-21 IPD
is used.
Continue as following:
−
Press
[
]
shortly. Green LED on the sensor flashes.
In the following steps the green LED switches off briefly for confirmation of the
settings.
−
Press
[+15 TIME]
more than 4 seconds to reset the switch-ON/-OFF time to
15 Minutes.
−
Press
[30 MIN]
or
[60 MIN]
briefly to parameterize the switch-ON/-OFF time
to 30 or 60 Minutes.
−
Press
[+15 TIME]
briefly to increase or
[
–
15 TIME]
to decrease the switch-
ON/-OFF time. If red LED flashes briefly, the minimum of 15 or the maximum
of 180 minutes is reached.
−
Press
[
]
briefly to save the settings. All LEDs on the sensor switch off for
confirmation.
Response value sensitivity
The response value sensitivity can be adjusted in four levels. If there are many
faulty circuits they can possibly be avoided by choosing a lower sensitivity level.
To change the sensitivity level the remote control
gesis
PIR IR B-04 IPD
is
necessary:
1. Press
[
]
briefly. Green LED on the sensor flashes for confirmation.
2. Press
[ZONE1]
long to choose the highest sensitivity. Red LED flashes for
confirmation.
3. Press
[ZONE2]
long to choose the second highest sensitivity. It is programmed
as described above.
4. Press
[ZONE3]
long to choose the second lowest sensitivity. It is programmed
as described above.
5. Press
[ZONE4]
long to choose the lowest sensitivity. It is programmed as
described above.
6. Press
[
]
briefly to end programming. All LEDs on the sensor switch off.
Dimensions
Detection range (MS8-360-SL)
The detection range can be extended by connecting a
slave
gesis
®
PIR MS8-360-SL
unit. Details see image below.
Doc. #
BA000957
– 06/2015 (Rev. A)
gesis
®
P MS8-360-1L | MS8-360-1Lb | MS8-360-1LSL | MS8-360-SLb | MS8-360-SLSL
EN
page
4
© 2015 All rights reserved. This description, including all the diagrams, is protected by
copyright. Third-party products are named without noting patent rights. The existence of
these rights must therefore not be ruled out. Changes of any type that are made in the
hardware or software of the products described result in an exclusion of liability on the part
of the manufacturer.
Wieland Electric GmbH
Brennerstraße 10-14
96052 Bamberg
Tel. +49 (951) 9324-0
Fax +49 (951) 9324-198
Internet: www.wieland-electric.com
Email: [email protected]
gesis
Hotline:
Tel.: +49 (951) 9324-996
Fax: +49 (951) 9326-996
Email: [email protected]
Internet: www.gesis.com
Installation Instructions (translation)
gesis
®
P MS8-360-1L
83.020.0110.1
gesis
®
P MS8-360-1Lb
83.020.0110.2
gesis
®
P MS8-360-1LSL
83.020.0110.3
gesis
®
P MS8-360-SLb
83.020.0111.1
gesis
®
P MS8-360-SLSL
83.020.0111.2
gesis
®
presence detector switching
Updated
:
06/2015
© 2015 Wieland Electric GmbH
