WiebeTech G5J Скачать руководство пользователя страница 4

G5JAM+ Installation Manual 

 

Phone: Toll Free 866.744.8722 Main 316.744.8722 • Fax: 316.744.1398 * 

[email protected]

 * 

[email protected]

 * 

www.wiebetech.com

 

 
 
If you have any questions or problems, please contact 

[email protected]

 for technical support.  If you 

are interested in purchasing more WiebeTech products, check our website or contact 

[email protected]

.  We appreciate being able to serve you! 

9. 

 

 

Install the side mounting plate. 

 
Set the three tabs on the bottom edge of the G5JAM into the three corresponding holes 
in the frame of the G5. The picture to the left is looking down into the G5. Be sure to 
support the Side Panel securely at all times during the installation. The Side panel is not 
permanently attached to the G5, so take great care when opening or closing the Side 
Panel. 

10.  

 

 

Connecting Power and Data cables to TOP drives. 

 
Attach the SATA cables to the hard disk drives. Any right angle connectors should be 
attached to the drives and the straight connectors should be attached to the PCI card 
connectors. The lower drive of the horizontally mounted drives can take a straight SATA 
Data connector. Attach one cable to the top drive first, then the second cable to the lower 
hard disk drive. Attach the Right angle connector to the top drive and the straight, flat 
connector to the lower drive. 

11. 

 

Connecting Power and Data cables to LOWER drives. 
 

Attach the Female ends of the Y-Power Connector to the power connectors on the hard 
disk drives. Be sure cables are routed safely out of the way when closing up the G5 
JAM/JAM+. 

 

 

 

12. 

 

 

Close it up. 
 

Take care that all cables are routed out of the way when closing the G5JAM Side Panel. 
If you have a full length PCI card in the top PCI slot, check to be sure there is adequate 
clearance for the hard disk drives while closing the Side Panel. If you run into clearance 
issues, you may want to reconfigure the drive arrangement if less than four drives are 
being installed. 
 
The original G5 side plate may now be re-attached. Be sure the release tab on the back 
of the G5 is in the up position when putting the original side plate in place. No one will 
ever know the speed and storage you have harnessed inside your G5. They will only 
wonder why theirs can’t do what yours does. Unless they have a G5 JAM/JAM+ too! 
 

When you restart your G5 you are ready to JAM! Use Disk Utility to format the new drives as singles or create a 
RAID of your choice. 

Содержание G5J

Страница 1: ...s are positioned on the card You will need to know how to connect the SATA cables to these connectors Install the SATA PCI card following any instructions provided with your G5 computer first If no instructions are available use these instructions as a guide Remove the retaining screw and blank slot cover for the PCI slot you wish to use Install the Serial ATA PCI card in one of the available PCI ...

Страница 2: ...he opening used for the IDE connector This is the same opening that will be used for the power connectors to pass through 2 Removing the DVD CD RW drive Next you will need to remove the DVD CD RW drive Release the two clamps that hold the drive in place The drive will slide straight out of the G5 You may have to slide the access door down and assist the removal from the front of the G5 Use extreme...

Страница 3: ...c board Do not cut through the insulation of the wires on the sheet metal 6 Slide the CD DVD drive back into position and lock the latches 7 Re connect the IDE cable from the CD DVD to the logic board 8 Connect the Y connector to the spare power lead brought down from the CD DVD and attach the two Serial drive power splitter connectors The four Serial drive power connectors are now ready to be con...

Страница 4: ...ATA Data connector Attach one cable to the top drive first then the second cable to the lower hard disk drive Attach the Right angle connector to the top drive and the straight flat connector to the lower drive 11 Connecting Power and Data cables to LOWER drives Attach the Female ends of the Y Power Connector to the power connectors on the hard disk drives Be sure cables are routed safely out of t...

Отзывы: