background image

Aquatronic 3 ultra

To adjust the shower temperature

The water temperature is altered by increasing or 
decreasing the flow rate of the water through the 
shower via the temperature control 

(fig.)

.

After obtaining your showering temperature, 
the number can be left as the normal setting 
and should only need altering to compensate for 
seasonal changes in ambient water temperature.

note:

 The preferred number on ECONOMy will 

give a different temperature to the same number 
position on HIGH.

To decrease the shower temperature

Turn the temperature control anti-clockwise; 
this will increase the flow of water through 
the shower therefore decreasing the water 
temperature, and is indicated by lower numbers.

To increase the shower temperature

Turn the temperature control clockwise; this will 
decrease the flow of water through the shower 
therefore increasing the water temperature, and 
is indicated by higher numbers.

note:

 It is advisable to be certain that the 

showering temperature is satisfactory by testing 
with your hand before stepping under the 
showerhead. There will always be a time delay of 
a few seconds between selecting a flow rate and 
the water reaching the stable temperature for 
that flow rate.

CaUtIon:

 It is recommended that persons 

who may have difficulty understanding or 
operating the shower controls should not 
be left unattended while showering. Special 
consideration should be given to young 
children and the less able bodied.

WarnInG!

after any servicing of mains water 

supply, always make sure the unit is 

started on CoLD in order to purge any 

air in the pipework.

note:

 In normal use, it is in order to leave 

the  water  supply  permanently  on  to  the 
shower  unit,  but  as  with  most  electrical 
appliances, 

the unit must be switched 

off at the isolating switch when not 
in use.

Warning!

This appliance is not intended for use 

by persons (including children) with 

reduced physical, sensory or mental 

capabilities, or lack of experience 

and knowledge, unless they have 

been given supervision or instruction 

concerning use of the appliance by a 

person responsible for their safety.

Children should be supervised to 

ensure that they do not play 

with the appliance.

Содержание TRITON Aquatronic 3 ultra

























Отзывы: