background image

Sierra Gold Trac Owner’s Guide 

1

ASSEMBLY -

1.

 Remove all parts from the shipping carton and check 

assembly diagram to ensure all parts are present. 

2.

 Install black rubber washers on fi ber clevis/lower 

rod, insert clevis lower rod onto loop ears. Use only 
nonmetallic washers, fi ber bolt, and fi ber thumb nut to 
secure loop/search coil to clevis/lower fi ber rod. 

3. 

Unlock “S” rod cam-lock and insert clevis/lower rod 

into curved “S” rod so that stainless steel spring clip 
buttons line up and lock into one of the adjustment 
holes in the curved “S” rod. Turn the cam-lock to se-
cure. The second or third adjustment holes are suitable 
for average sized adults. 

4.

 Wind the loop cable around the rod assembly, fi rst 

revolution over the top of the rod, all the way to the top 
of the curved “S” rod, about fi ve revolutions. Use the 
black cable retainers, one near the loop, and one near 
the top of the curved “S” rod, to hold the loop cable in 
place. Plug the cable into the jack on the front of the 
control box. 

5. 

Grip the instrument by the handle, with your 

arm in the elbow cup with strap and sweep the 
loop/search coil over the fl oor. If the instrument 
fi t feels uncomfortable, readjust clevis/lower rod 
length with spring clip button and cam-lock so 
that the search coil can be held near the fl oor 
without stooping over. 

6. 

Remove the protective paper from the two 

black arm cup foam pads. Carefully align pads 
on the inside of the elbow cup, one on each side 
of the center rod, and press fi rmly into place. 

7. 

Adjust the elbow cup strap so that it is loose 

enough for you to slide our arm in and out 
without loosening each time you want to set the 
detector down. The elbow cup strap provides ex-
tra leverage and control. However, some prefer 
not to use it.
 

8. 

Install the battery pack; *make sure not to put 

the batteries in upside down.

Rubber

washers (2)

fi ber bolt

Clevis

Cam-lock

Battery door

Search coil

Lower rod

Arm cup

Содержание SIERRA GOLD TRAC









Отзывы: