White Outdoor 24AD595C190 Скачать руководство пользователя страница 6

Страница: 6 / 20

WARNING: Disconnect the spark plug wire
and ground against the engine to prevent
unintended starting.

Assembling The Tongue

Attaching The Beam Support/Latch Bracket (See Figure 1)

•

Remove two hex bolts, lock washers, and hex nuts
from the tongue.

•

Place the beam support/latch bracket on the
tongue and secure with the hex bolts, lock washers,
and hex nuts previously removed. Tighten securely.

Figure 1

Attaching The Adjustable Jack Stand

(See Figure 2)

•

Remove four hex bolts, lock washers, and hex nuts
that secure jack stand mounting brackets to
adjustable jack stand.

•

Place adjustable jack stand halfway between beam
support/latch bracket and end of tongue.

Figure 2

•

Insert hex bolts through top holes in jack stand
mounting brackets and holes in the adjustable jack
stand. Secure with lock washers and hex nuts.

•

Insert hex bolts through upper holes in the bottom
of the mounting brackets and adjustable jack stand.
Secure with lock washers and hex nuts.

•

The adjustable jack stand is raised by turning the
crank clockwise and lowered by turning counter-
clockwise.

Attaching The Hitch Assembly (See Figure 3)

•

Remove the hardware assembled on the hitch
assembly and place the hitch on the end of the
tongue.

•

Insert hex bolt through flat washer, end of safety
chain, spacer, and then rear hitch hole. Pivot the
end of safety chain so it faces the ball end of hitch.

Figure 3

•

Insert other spacer, safety chain, and flat washer
on the other end of the hex bolt and secure with hex
lock nut.

•

Insert hex bolt through the front hole of hitch and
secure with flat washer and hex lock nut. Tighten
both hex nuts to 23 ft-lbs.

Assembling The Wheels, Tongue, and
Beam

Attaching The Wheels To The Reservoir Tank Assembly
(See Figure 4)

•

Block up the reservoir tank assembly about eight to
twelve inches.

•

Remove and discard plastic shipping caps on the
outside of the wheels.

•

Remove the cotter pin, hex slotted nut, and flat
washer from each axle.

NOTE: It is recommended that you polish the axles with
emery cloth before you install the wheels.

Beam Support
Latch Bracket

Hex Bolts

Lock
Washer

Tongue

Hex Nut

Hex Bolts

Mounting
Brackets

Tongue

Adjustable
Jack Stand

Lock Washer

Hex
Nuts

Tongue

Hex
Bolt

Flat
Washer

Spacer

Hex

Hex
Bolt

Lock Nut

Hitch

Assembly

Chain

Содержание 24AD595C190





















Результаты поиска

Содержание 24AD595C190

Отзывы:

Похожие инструкции для 24AD595C190

Бренды по названию

Популярные бренды

White Outdoor 24AD595C190, Руководство оператора

Результаты поиска

Содержание 24AD595C190

Отзывы:

Похожие инструкции для 24AD595C190

Бренды по названию

Популярные бренды