WhisperKool Phantom 3500 Скачать руководство пользователя страница 11

Страница: 11 / 39

www.whisperkool.com | Page 9

Phantom Series

Ambient Temperature Factor

The cooling unit has the ability to cool a wine cellar efficiently to 55°F as long as the ambient temperature of the area that it is

exhausting to does not exceed 110°F. Therefore, you want to exhaust the unit in a room which will stay between 42°F and 110°F.

Without proper heat dissipation the unit will not have the capacity to keep the wine at a desirable 55°F.

Ventilation

The necessity of dissipating heat away from the unit is critical to the unit’s performance and cannot be overstated. As the unit

operates and cools, a greater amount of heat is generated on the exhaust side of the unit. Adequate ventilation is required in

order to dissipate heat away from the unit. If ventilation is inadequate, the exhaust will heat the area or room and adversely

affect the unit’s ability to cool. In some cases, it may be advisable to install a vent fan to dissipate heat from within the exhaust

area. However, you must have a fresh air inlet as well.

Using any other ducting system will void the warranty.

Note:

If you are unsure whether you have adequate ventilation in your install location, please

WARNING! Allowing your unit to operate in high ambient temperatures for extended

periods of time will greatly decrease the life of your unit and void your warranty.

Wine Cellar

Mechanical Room

FOR ILLUSTRATION PURPOSES ONLY

Содержание Phantom 3500








































Результаты поиска

Содержание Phantom 3500

Отзывы:

Похожие инструкции для Phantom 3500

Бренды по названию

Популярные бренды

WhisperKool Phantom 3500, Руководство пользователя

Результаты поиска

Содержание Phantom 3500

Отзывы:

Похожие инструкции для Phantom 3500

Бренды по названию

Популярные бренды