WhisperKool 4000 Condenser Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 58

background image

www.whisperkool.com | Page 25

LIQUID TEMPERATURE - MEASURING THERMOSTAT

The WhisperKOOL Series cooling units come equipped with a liquid temperature measuring thermostat. This incorpo-

rates the following advantages:

1. Wine is kept in a very precise, controlled environment. This assures a consistent temperature.
2. By measuring liquid rather than air, the cooling unit is protected from rapid cycling caused by fluctuations in air

temperature.

Liquid Temperature - Measuring Thermostat

To assure a consistent temperature, place bottle probe at least 3 feet away from the air output and not in the flow of the air.

To Use the thermostat:

1. Locate an empty wine bottle.

2. Fill 3/4 full with room temperature tap water.

3. Place bottle probe securely into bottle.

4. Place bottle with probe level and to the side of the unit in your

wine cellar.

It is recommended that it be placed in a central location

of your wine cellar.

Avoid pulling too much on the probe cord. It

may become disconnected resulting in non-operation of the unit.

Note: The thermostat can be set between 50°F

and 67°F.

Remember: The WhisperKOOL unit operates based on the

temperature of the water. Do not be misled by thermostats

reading air temperature. The air temperature in the cellar will be

cooler than the liquid temperature of the wine while it is reaching

optimum balanced temperature.

«
...
25
26
27
28
29
...
»

Содержание 4000 Condenser



























































Отзывы:

Нет отзывов

Похожие инструкции для 4000 Condenser

Бренд: Haier Страницы: 60

Бренд: Acekool Страницы: 24

Бренд: Jafanda Страницы: 6

Бренд: GE Страницы: 28

Carry-Cool AT505

Бренд: GE Страницы: 8

Бренд: GE Страницы: 20

Бренд: GE Страницы: 48

Бренд: GE Страницы: 56

Бренд: Carrier Страницы: 104

Premium CR 7926

Бренд: camry Страницы: 156

DYNAPACK S Series

Бренд: Suburban Страницы: 22

Бренд: GE Страницы: 32

Бренд: Daikin Страницы: 335

Бренд: TECO Страницы: 15

GWH18AAD-K6DNA1A/I

Бренд: Gree Страницы: 121

22-11-2222N-003

Бренд: Maytag Страницы: 26

Бренд: SystemAir Страницы: 72

Бренд: Daikin Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды