background image

 
 
 
 
 
TROUBLE SHOOTING 

 

 

 

34

 

January 2009 / W-SQ12 for mobile applications / EN 

5.4.3 

Disassembling instructions  

 

It  could  be  necessary  to  disassemble  the  generating  set 

for repair or checks. Following instructions will help:  

 

The  design  of  the 

W-SQ12

  makes  it  possible  to  do 

most  repairs  on  the  spot.  The  connections  of  the 

alternator  are  very  accessible.  The  same  is  true  for 

the diode of the rotor 

The  sound  shield  can  be  disassembled  according  to 

exploded view below (figure 28). 

To take the generating set out of the canopy all hose 

and cable connections have to be taken off. The set is 

fixed to its base by four rubber mountings and can be 

loosened  by  removing  the  four  nuts  from  the  bolts  of 

these  mountings.  The  easiest  way  to  get  the 

generator out of its capsule is by lifting the set with the 

aid of the lifting eyes. 

One  can  take  off  the  complete  alternator  housing. 

Before  the  alternator  can  be  taken  off  all  cables  and 

wiring has to be taken loose first. 

The rotor can be taken off by removing the bold which 

goes  through  the  shaft  (normal  clockwise  threaded). 

The end of the shaft is specially threaded to push off 

the  rotor  from  the  conic  stub  shaft,  which  is  on  the 

flywheel, using a 10-mm rod of 245 mm length and a 

M24x2 bolt. 

Reassembling  the  generating  set  one  should  take 

care  of  alignment,  cleaning  the  surfaces  between 

engine  and  alternator and  tighten  the bolts crosswise 

and gradually.  

Use  Loctite 577  to seal  the  fittings,  which  should  first 

be cleaned and made free of oil and grease. 

Test  the  generating  set  first  outside  its  capsule  and 

check  very  carefully  for  leakages  before  putting  it 

back in its enclosure.  

 

 

 

Figure 28: exploded view sound shield 

W-SQ12

 

 

Содержание W-SQ12









































Отзывы: