WHISPER KOOL SLIMLINE LS Скачать руководство пользователя

Страница: 12 / 30

Page 10 | 1-800-343-9463

SL 072820

Electrical Needs

The Slimline system requires a dedicated 115V, 15-amp circuit. The unit draws a large amount of amps during its

initial startup. By designating a dedicated circuit breaker, you will guarantee that the unit has enough power to run

effectively. Contact an electrician for assistance with the installation of this dedicated electrical circuit:

•

Match the electrical outlet to the plug provided on the WhisperKOOL unit.

•

Provide a dedicated circuit and wiring for the unit.

Electrical Outlet

The accessory kit includes an 8-foot power cord which is connected to the power inlet on the side of the unit. Plug

your WhisperKOOL unit into a surge protector or power conditioner. Power surges and spikes can damage sensitive

electrical equipment. WhisperKOOL recommends plugging the unit into a surge protector or power conditioner in

order to protect your system. As outlined in our terms and conditions, power surges and spikes are not covered under

warranty.

WE RECOMMEND THAT YOU DO NOT USE A GROUND FAULT INTERRUPTER (GFI) WITH THIS PRODUCT.

NOTE:

GFI’s will often nuisance trip with certain types of loads. For example, compressor motors will trip

on GFI even though there is no leakage to ground.

Test Preparation Procedure

Remove unit from box

Place unit on tabletop

Plug unit into an electrical outlet

Plug in bottle sensor

Turn on to test (temperature differential should be 10°F across coils)

Turn off after test

Remove bottle probe

Testing the Unit

Place the WhisperKOOL system on a tabletop to prepare it for installation and testing. Plug the unit into a live electrical

outlet and turn it on. The unit may take up to 10 to 15 minutes before running cool. Once the operation has been

tested, turn the unit off and unplug it from the electrical outlet.

Units weigh 81 pounds and are cumbersome for one person to carry. We recommend that you get someone else to

help you during the installation process. NEVER LAY UNIT ON ITS SIDE.

If the system does not seem to be running cool after 15 minutes, please refer to the Troubleshooting Guide on page
22.

PRE-INSTALLATION

Skill level: Moderate

Follow local building codes and/or consult a licensed contractor

Содержание SLIMLINE LS































Результаты поиска

Содержание SLIMLINE LS

Отзывы:

Похожие инструкции для SLIMLINE LS

Бренды по названию

Популярные бренды

WHISPER KOOL SLIMLINE LS, Руководство пользователя

Результаты поиска

Содержание SLIMLINE LS

Отзывы:

Похожие инструкции для SLIMLINE LS

Бренды по названию

Популярные бренды