background image

3

Parts Supplied

For information on ordering, see “Replacement Parts” section. 

Location Requirements

Check the opening where the microwave oven will be installed. 
The location must provide:

Minimum installation dimensions. See “Installation 
Dimensions” illustration.

Side cabinets: Support for weight of 75 lbs (34 kg) each, 
which includes microwave oven and items placed inside the 
microwave oven and side cabinets.

Grounded electrical outlet inside upper cabinet. See 
“Electrical Requirements” section.

NOTES:

Installation requires venting above the microwave oven.

Recirculation installation requires venting through a kitchen 
soffit. See “Venting Requirements” section. A charcoal filter 
kit should be used for recirculation. See “Assistance” section 
for information on ordering.

If you are using a rectangular to round transition piece, 3" 
(7.6 cm) clearance needs to exist above the damper 
assembly so that the damper blade can open freely and fully. 
See “Rectangular to Round Transition” illustration in “Venting 
Requirements” section.

Some cabinet and building materials are not designed to 
withstand the heat produced by the microwave oven for 
cooking. Check with your builder or cabinet supplier to make 
sure that the materials used will not discolor, delaminate or 
sustain other damages.

Installation Dimensions

NOTE: The grounded 3 prong outlet must be inside the upper 
cabinet. See “Electrical Requirements” section. 

*Measure from the front edges of the side cabinets.

**For installation with stainless steel filler panel.

NOTE: To avoid stress on the power cord, a minimum of 1

¹⁄₂

(3.8 cm) must exist between the top surface of the microwave 
oven’s upper component housing and the bottom of the upper 
cabinet.

Product Dimensions 

A. L-brackets (2)
B. Rear trim

C. Bottom plate
D. Visor

E. Grease filter

F. Damper assembly

G. 16 mm wood screws (10)

H. 9.5 mm metal screws (10)

I. 16 mm round-head bolts (2)

J. 17 mm shoulder screws (2)

K. Washers (2)

L. Hex key

M. Leveling screws (4)

A

B

C

D

E

F

G

H

I

J

K

L

M

A. Grounded 3 prong outlet

A

11

¹⁵⁄₁₆

" (30.3 cm) min.

13

³⁄₄

" (34.9 cm) max.

21" (53.3 cm) min.
21

⁵⁄₈

" (54.9 cm)**

39" (99.1 cm) min.

23

⁷⁄₈

(60.6 cm) min.*

24

¹⁄₈

(61.2 cm) max.*

23

⁹⁄₁₆

" (59.8 cm)

12

⁵⁄₈

" (32.0 cm)

20

⁷⁄₁₆

"

(51.9 cm)

16

¹⁄₈

"

(40.9 cm)

11

¹³⁄₁₆

" (30.0 cm)

Содержание YUMV4084BS0













Отзывы: