background image

3

Clean Before Using

After you remove all of the packaging materials, clean the inside of your 
freezer before using it. See the cleaning instructions in “Caring for Your 
Freezer.”

Location Requirements

Ventilation and Clearance

Keep flammable materials and vapors, such as gasoline, away from 
freezer.

Do not cover the freezer with items such as blankets, sheets, 
tablecloths, etc. This reduces air circulation. 

Allow at least 3" (7.5 cm) of air space at the top and on both sides 
of the freezer and 1" (2.5 cm) between the back of the freezer and 
the wall. If the freezer is to be next to a fixed wall, leave extra space 
on the hinge side so the door can open wider.

Temperature

Your freezer operates most efficiently when located in an area where 
the temperature will not fall below 40°F (5°C). Place your freezer in a 
location where the temperature will not fall below this recommended 
temperature.

Upon Moving to Final Location

NOTE:

 Allow for a 3" (7.5 cm) clearance at the top and sides and a 

¹⁄₄

(6.4 mm) clearance between the appliances.

Electrical Requirements

Before you move your freezer into its final location, it is important to 
make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical 
supply is required. It is recommended that a separate circuit serving 
only your freezer be provided. Use an outlet that cannot be turned off 
by a switch. Do not use an extension cord.

NOTE:

 Before performing any type of installation, cleaning, or removing 

a light bulb, press and hold TEMP SETTING for 3 seconds to turn off 
cooling, and then disconnect the freezer from the electrical source.

Important information to know about glass shelves 
and covers:

Do not clean glass shelves or covers with warm water when 
they are cold. Shelves and covers may break if exposed to 
sudden temperature changes or impact, such as bumping. 
Tempered glass is designed to shatter into many small, 
pebble-size pieces. This is normal. Glass shelves and covers 
are heavy. Use both hands when removing them to avoid 
dropping.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as 
gasoline, away from freezer.

Failure to do so can result in death, explosion, or fire.

 3" (7.5 cm)

 3" (7.5 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, 
fire, or electrical shock.

WARNING

Содержание WZF56R16














Отзывы: