Whirlpool WWDC 9614 S, Инструкция по эксплуатации

Страница: 6 / 38

6
When installing the appliance
make sure that the four feet are
stable and resting on the floor,
adjusting them as required,
and check that the appliance is
perfectly level using a spirit
level .
In the case of installation on
wood or floating floors,
position the washer dryer on a
plywood panel that has been
fixed to the floor, which must
be at least 60 x 60 cm in size,
and at least 3 cm thick .
Use only new hoses to connect
the appliance to the water
supply . Used hoses must not
be used and should be
discarded .
Do not move the washer dryer
while holding onto its upper
surface .
Connect the water inlet hose(s)
to the water supply in
accordance with the
regulations of your local water
company .
For models dedicated only for
cold water: Do not connect to
the hot water supply .
For models with hot fill: the hot
water inlet temperature must
not exceed 60 °C .
Make sure that the ventilation
openings in the base of your
appliance (if available on your
model) are not obstructed by a
carpet or other material .
The supply water pressure
must be in range 0 .1 -1 MPa .
The appliance must not be
installed in such a way as to
impede its door from opening
completely (e .g . behind a
lockable door, a sliding door, or
a door that is hinged on the
side opposite to that of the
appliance itself) .
ELECTRICAL WARNINGS
Make sure the voltage
specified on the rating plate
Do not stop the appliance until
the drying cycle has been
completed;if this should be
necessary, quickly remove all
the garments and lay them out
in order to facilitate the heat's
dissipation .
The last phase of the drying
cycle is done without heat
(cool down phase), to assure
that the laundry stays at a
temperature level which is not
leading to a damaging of the
laundry .
INTENDED USE OF THE
PRODUCT
This appliance is designed
solely for domestic usage . To
aim the appliance as
professional use is forbidden .
The manufacturer declines all
responsibility for inappropriate
use or incorrect setting of the
controls .
CAUTION
: The appliance is
not intended to be operated
by means of an external timer
or separate remote control
system .
Do not use the appliance
outdoors .
Do not store explosive or
flammable substances such as
aerosol cans and do not place
or use gasoline or other
flammable materials in or near
the appliance: a fire may break
out if the appliance is
inadvertently switched on .
This appliance is designed
exclusively for domestic use
with loads of laundry that can
be washed and spun in a
washer dryer machines .
INSTALLATION
Installation and repairs must
be carried out by a qualified
technician, in compliance with
the manufacturer’s instructions
and local safety regulations . Do
not repair or replace any part
of the appliance unless
specifically stated in the user
manual .
Children should not perform
installation operations . Keep
children away during
installation of the appliance .
Keep the packaging materials
(plastic bags, polystyrene
parts, etc .) out of reach of
children, during and after the
installation of the appliance .
Use protective gloves to
perform all unpacking and
installation operations .
After unpacking the appliance,
make sure that it has not been
damaged during transport . In
the event of problems, contact
the dealer or your nearest
Customer Support Service .
The appliance must be
handled and installed by two
or more persons .
Keep children away during
installation of the appliance .
The appliance must be
disconnected from the power
supply before carrying out any
installation operation .
During installation, make sure
the appliance does not
damage the power cable .
Only activate the appliance
when the installation
procedure has been
completed .
After installation of the device
to wait a few hours before
starting it, to acclimatise to the
environmental conditions of
the room .
Do not install your appliance
where it may be exposed to
extreme conditions, such as:
poor ventilation, temperature
below 5 °C or above 35 °C .