4
Alternate Parts
Your installation may require additional parts. For information
on ordering, please refer to the back cover of this manual.
If You Have:
You Will Need to Buy:
Laundry tub or standpipe
taller than 72" (183 cm)
Sump pump system
(if not already available)
1" (2.5 cm) diameter
standpipe
2" (5 cm) diameter to
1" (2.5 cm) diameter
standpipe adapter,
Part Number 3363920
Overhead sewer
Standard 20 gal. (76 L)
39" (990 mm) tall drain tub
or utility sink, sump pump,
and connectors (available
from local plumbing
suppliers)
Floor drain
Siphon break, Part Number
285320; additional drain
hose, Part Number 3357090
and connector kit,
Part Number 285442
Water faucets beyond reach
of fill hoses
2 longer water fill hoses:
6 ft (1.8 m)
Part Number 76314
10 ft (3.0 m)
Part Number 350008
Drain hose too short
Drain hose, Part Number
388423 and hose kit,
Part Number 285442
Drain hose that is too long
Hose kit, Part Number
285442
Lint clogged drain
Drain protector,
Part Number 367031
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room,
closet, or recessed area. See “Drain System.”
Washer Dimensions
37"
(940 mm)
23"
(584 mm)
21"
(533 mm)
3
/
4
"
(19 mm)*
*Minimum measurement with leveling feet installed.
IMPORTANT:
Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
■
A water heater set to deliver 120°F (49°C) water to
the washer.
■
A grounded electrical outlet located within 5 ft (1.5 m) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■
Hot and cold water faucets located within 3½ ft (1.1 m) of
the hot and cold water fill valves, and water pressure of
5–100 psi (34.5–690 kPa).
■
A level floor with a maximum slope of ¾" (1.9 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
■
A sturdy floor to support the washer weight (washer, water,
and load) of 225 lbs (102 kg).
Do not store or operate your washer in temperatures at or
below 32°F (0°C). Some water can remain in the washer and
can cause damage in low temperatures. See “Washer Care”
for winterizing information.
Recessed area or closet installation
The dimensions shown are for the recommended spacing
allowed, except the closet door ventilation openings. The
dimensions shown for the closet door ventilation openings
are the minimum required.
■
Additional spacing should be considered for ease of
installation and servicing.
■
Additional clearances may be required for wall, door,
and floor moldings.
■
Additional spacing of 1" (2.5 cm) on all sides of the washer
is recommended to reduce noise transfer.
■
If a closet door is installed, the minimum air openings
in the top and bottom of the door are required. Louvered
doors with air openings in the top and bottom are
acceptable.
■
Companion appliance spacing should also be considered.
Washer Only
12"
(305 mm)
4"
(102 mm)
3"
(76 mm)
3"
(76 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
1"
(25 mm)
1"
(25 mm)
1"
(25 mm)
Closet door with vents
Recessed area
Содержание WTW2000HW
Страница 2: ...2 WASHER SAFETY ...
